Question about Cars & Trucks

Open Question

I have a infinity QX56 2011 I put a bull bar and every time I go reverse the warning signals turn on that I have some thing to close to me in the front.is there any way I can make that noise to stop?

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Zlobomir
  • 225 Answers

SOURCE: car was making a whirring noise and got louder and

Check alternator brushes, bearings, the driving belt... As per the steering, probably a low-voltage issue...

Posted on Nov 10, 2009

  • 1 Answer

SOURCE: Beeping Noise/Blinker Noise

I thought the same thing. In the past with this car that was the case, it needed a lightbulb replaced somewhere on the car. So after replacing 4 lightbulbs on the car, it still makes the noises...question for someone: I did notice that when i open the doors on the car, the dome light does come on but there are no lights down by the floor in the front of the car...if these bulbs are burnt out too then I will need to replace these and maybe the ticking noises will stop? Are there lights for the floor area on the 2003 Alero model?

Posted on Mar 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

10 sec sound when selecting reverse. reverse alarm not bleeping on reversing near obstacle.


the beep is a warning of system failure the usual problem is water in the sensors, to test the sensors engage reverse with ign. on and put your ear close to each sensor in turn you should hear a faint ticking from the good sensors, nothing from the faulty ones, the wiring behind the bumper is also prone to burning on the exhaust. hope this helps.

Mar 18, 2015 | 2003 Jaguar X-Type

1 Answer

How to fit bull bars on VW Transporter T5


AS the fitment of bull bars to vehicles negates the operation of the air bags , this operation should be left to the experts who have designed the bars to not affect the safety systems of the vehicle . IT may appear expensive but consider what your life is worth if fitted incorrectly.. There are plenty of Off road shops who sell and fit bull bars so talk with them as to how it should be done.

May 13, 2014 | 2006 Volkswagen Transporter 1.9

1 Answer

Kia sedona problems


Not sure about yours but most newer 2010 and up Sedona's have backup warning signal and if yours does it sounds like it's covered with something and every time you put the vehicle in reverse it will go off.

Nov 24, 2013 | Cars & Trucks

1 Answer

96ChryslerCirrus: 'door' warning vs odometer miles, Dome light stays on.


In the Ford Ranger, the light switch can be found in the door, right by the latch. You may need to use some WD-40 to get to work properly. -------------------------------------------------------------------------------------
zed bull

Nov 28, 2012 | 1996 Chrysler Cirrus

2 Answers

Cant get the bolts loose to remove brake caliper bracket, are they reverse thread?


No there right handed try hitting with propane touch 30 seconds or so spray it with wd 40 and try to break it free its funny there usely not bad to lossen unless they got real hot for some reason well good luck

Nov 24, 2010 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

Yellow warning light on message says bulb position failure Cannot find in manuel Thanks Howie


Have some one work all the light's while you check them, running lights, stops lights, turn signal lights, there's a burn out light bulb some where that needs to be replace.

Jul 19, 2010 | 2003 Volvo S60

2 Answers

I have the warning indicator on that reports a light bulb is burned out, but all my lights are on and appear to be working. What is the best approach to this problem?


Double check all the lights. Pay close attention to the reverse lights and all the turn signal lamps. The reverse is the most commonly over looked. Have some with you while checking these lamps to confirm. Also check rear licence plate light. Failing that unplug a bulb, any (the easiest), with all the running and headlights on. Plug it back in and check warning light again this my reset it.

Dec 18, 2009 | 2001 Toyota Camry

1 Answer

1999 Infinity QX4. Door Open warning light


usually on post where door closes, or in jamb by hinge area. Open door & try pushing any button/pin like object or may be a lever style too, with thumb or finger.When interior light goes out, you found it

May 03, 2009 | 1999 Infiniti.5 QX4

1 Answer

'96 F-250 Diesel Brake lights and left turn signal malfunction


the easiest way to check if u have a bad earth is to get jumper leads and place the negative side of battery the other end on metal part of the body with no paint on it bull bar and check it again see how u go

please rate

Dec 17, 2008 | 1995 Ford F250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...