Question about Cars & Trucks

Open Question

2005 cc precedent won't move. At first would buck then go. Now wont move. Replaced MCOR,put high speed motor magnet in. The magnet cracked upon install. Still doing the same thing before new parts.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dofsqaa
  • 169 Answers

SOURCE: Wiper Motor keeps getting stuck

The new one you bought if its secound hand might be dead

Posted on Aug 16, 2008

Ad
  • 6982 Answers

SOURCE: Describe your 1988 jeep Cherokee hesitate bucks

You mentioned nothing regarding the ignition system (cap rotor, wires coil)...checked those?

Posted on Dec 14, 2009

conrynsilver
  • 56 Answers

SOURCE: 2006 2500 ram truck deisal.

Bad wiper relay.

Posted on Oct 25, 2010

  • 395 Answers

SOURCE: 2005 Jeep Liberty Heater fan motor speed control

Sounds like low speed coil in the Blower Fan resistor block has failed. The Blower Fan Resistor Block is usually located in the air ducting adjacent to the Blower Fan. The Resistor Block consists of 3 or 4 coils of special resistance wire attached to terminals which connect to the wiring that comes from the fan switch and then to the Blower Fan. The block is on the output side of the fan unit so that the airflow from the fan past the coils inside the duct assists in preventing them from overheating and burning out.
Access to the Resistor Block is from under the dash. To replace, remove the multi-pin connector and then undo the screws holding in the block. Check air duct for leaves and dirt which may have caused the coils to fail. .Replacement is the reverse procedure

Posted on Nov 27, 2010

daves944
  • 1050 Answers

SOURCE: Heater motor speed control. only

You'll need to replace the blower motor resistor. It controls the current to the lower speeds and it is mounted in the blower housing.

daves944_6.jpg

Posted on Feb 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan quest 2005 SE rear blower motor heat is in high speed i put a new resistor and still same problem


NISSAN QUEST 2005 SE ,FRONT BLOWER RUNS AT HIGH SPEED ON HEAT/AC,EVEN WHEN THE LED INDICATORS SHOWS DIFFERENT SPEED

Mar 18, 2013 | Cars & Trucks

1 Answer

Audi A8 a/c compressor wont engage i have voltage power to the system


You have applied 12 volts and a good ground to the compressor magnetic closing coil from the battery and it still won't close and engage conpressor? it that what you are saying? If so the magnetic closing coil is defective, you will need special tools to pull it off and replace it.

Sep 12, 2012 | 2005 Audi A8

1 Answer

Cooling fans won't run on high.


The diagram is a little hard to follow, but it looks like on the high fan relay there are 5 circuits like on the hi-low relay.
Pin 86 is power for the magnet, 85 is the ground signal from the module. The module grounds the magnet to move the contacts.
Pin 30 goes to the fan and pin 87 goes to a 50amp fuse.
Pin 87A is a jumper between the two relays.
The fan motor gets power from three different sources and is grounded to the car. The other two wires are return signals to the module. Kind of like a three way light switch in a house.
On the fan control relay, pins 30 and 85 are hot, pin 87 goes to the fan motor, and pin 86 is grounded by the module.
I can send you the diagram in a separate message if you need to see it.

Jul 28, 2012 | 2005 Chrysler 300

1 Answer

I put 2005 Nissan Altima on computer and it reads "engine speed input malfunction". The car dies going down the road and hesitates to crank back up.


you need acrankshaft position sensor.while your at it replace cam sensor.same exact sensor same price and same high rate of failure.for another 60 bucks you'll save yourself alot of grief.

Feb 01, 2011 | 2005 Nissan Altima

2 Answers

2005 jeep AC and heater blower only high speed works


check fuses, then wiggle speed control while moving, may need new dash control for lower speed, usually high speed works through relay may be the reason high speed works

Nov 03, 2010 | 2005 Jeep Grand Cherokee

6 Answers

2005 Pontiac Vibe heater fan working on high only


My 2005 Vibe did the same thing it was the heater resistor. It is located to on the firewall behind the glove box on the lower left side of the blower assembly. Two 5.5mm screws hold it in place (1/4 inch socket works too). I used a socket attached to a socket swivel to replace mine in under 10 minutes. Heater now works as good as new. I purchase mine online for $30 from rockauto.

Jul 31, 2009 | 2005 Pontiac Vibe

1 Answer

2005 chevy trailblazer, fan switch wont work on all speeds


Had the same problem on my 2005 trailblazer I replaced the resister and wire harness because wire harness was burnt on a few connections. Cost was 75 bucks for both parts at Napa auto parts works fine now

May 23, 2009 | 2005 Chevrolet Trailblazer Ext

1 Answer

Crankshaft Sensor


what ever u mounted fom the old flywheel was not a magnet....the magnet is internal to the cranksensor and the flywheel slots trigger the sensor....whatever you attached maybe causing this code

Oct 14, 2008 | 1998 Dodge Ram 1500 4WD

1 Answer

Fan motor noise 2005 t bird


do you have a mechanical or a electric fan?
acording to your question seems to be electrical make sure the fan nut is tie and there is no cracks on blades
also wigle the ft shaft up and down and if you feel any play the replace the motor

Jun 01, 2008 | 2005 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...