Question about Cars & Trucks

1 Answer

I need the nuts and bolts to install a front bumper for 2005 Silverado LS.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,363 Answers

Call the Dealer,not that much,they will order them for you.

Posted on Apr 29, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a front bumper


The old-style chrome-plated metal bumpers are much simpler to replace than the newer-style ones are, but are much heavier. An assistant may be needed to hold the bumper in place while starting the fasteners.
These bumpers are held in place by four carriage bolts. The heads of these bolts are kept from rotating by a square cutout in the metal of the bumper. Immediately behind the head of the bolt is a square area on the shaft that fits this cutout exactly.
Before trying to loosen the bolts, spray them with WD-40 or another light lubricating oil. If the threads of the bolts are rusted, use a drill-mountedwire brush to clean off as much of the rust as possible. The nuts can be removed from these bolts with a ratchet and socket. A breaker bar may be necessary to start loosening the nuts. Be sure to keep the head of the bolt flush up against the metal of the bumper so that it will not turn.
Once the four bolts are removed, the bumper should fall off. The new bumper can be placed onto the mounting brackets and the hardware re-installed. If the hardware is rusty, it is recommended to replace it with new hardware.

Mar 24, 2016 | 2005 Chrysler Pacifica

2 Answers

Front license plate install


Most factory kits come with the hardware to install it will be plastic push ins, bolts with j-nuts, or pointed hex head bolts. The push ins just push in line up the plate holder to the holes in bumper, if bolt and j-nut must slide j-nuts into slots then line up and install, if pointed bolts there are dimples that can be seen in bumper install at dimples, if no dimples just line up and install.

Aug 16, 2014 | Cars & Trucks

1 Answer

What nuts/bolts/fasteners do I need to remove to get the front bumper off 2005 Toyota Avensis and where are they located?


They are clearly visible behind the front bumper both up top and the bottom, crawl under.

Oct 01, 2012 | Cars & Trucks

1 Answer

2011 Dodge Caravan. Ran into a metal wheelchair ramp rain. Drove back - dislodged - the black trim insert near the bottom of the plastic bumper cover. That black plastic thing has to be just put back on...


Hello Bruce...here are the steps to follow per All Data.

Release hood latch and open hood.
Remove the headlamp assemblies.
Hoist vehicle and support with safety stands.
Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
Remove front wheels.
Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
Disconnect fog lamp wire connectors, if necessary.
Lower vehicle.
Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
Remove bumper fascia from vehicle.
INSTALLATION

Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
Hoist vehicle and support with safety stands.
Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
Install front wheelhouse splash shields fasteners.
Install front wheels.
Connect fog lamp wire connectors, if necessary.
Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
Lower the vehicle.
Install the headlamp assemblies.

The "push pin fasteners" are the pain you are having i believe. They push in, but to get them out you need squeeze them on the back & pull at the same time. If you happen to break a few, you can buy them in various sizes at the auto parts store. I hope this information is helpful, an owners manual will not have any info like this in it.



12_2_2011_5_37_49_pm.jpg

Dec 02, 2011 | Cars & Trucks

1 Answer

I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


  1. Release hood latch and open hood.
  2. Remove the headlamp assemblies.
  3. Hoist vehicle and support with safety stands.
  4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
  5. Remove front wheels.
  6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Fig. 1 133387737
Fig. 2 133387738

  1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
  2. Disconnect fog lamp wire connectors, if necessary.
  3. Lower vehicle.
  4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
  5. Remove bumper fascia from vehicle.
INSTALLATION


  1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
  2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
  3. Hoist vehicle and support with safety stands.
  4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
  5. Install front wheelhouse splash shields fasteners.
  6. Install front wheels.
  7. Connect fog lamp wire connectors, if necessary.
  8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
  9. Lower the vehicle.
  10. Install the headlamp assemblies.

Jan 02, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

2002 ford escape passanger side headlamp assembly removal?


Removal and Installation
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. NOTE: Pull headlamp assembly forward to access electrical connectors.
    Remove the headlamp assembly.
    1. Remove the three bolts.
    1. Loosen the nut.
    • Disconnect the electrical connectors.
    a0045726.gif
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Mar 03, 2009 | 2005 Ford Escape

2 Answers

Need to replace headlight assembly on 2005 Ford Escape


ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

n0037234.gif
Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 3 headlamp assembly bolts.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the headlamp assembly nut and the headlamp assembly.
    • Disconnect the electrical connectors.
    • To install, tighten to 5 Nm (44 lb-in).
  1. To install, reverse the removal procedure.

Jan 01, 2009 | 2005 Ford Escape

1 Answer

Replacing starter 02 silverado 6.6


  1. Remove or disconnect the following:
    • Negative battery cables
    • Right front wheel and fender splash shield, on 6.6L engines
    • Turbocharger exhaust pipe, on 6.6L engines
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152801cad96.jpgExploded view of the starter motor-6.5L engine shown
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires.Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18inch lbs. (2 Nm) on 6.5L engines. On 6.6L engines, tighten the solenoidnut to 30 inch lbs. (3.4 Nm) and the positive battery cable nut to 80inch lbs. (9 Nm).
    • Starter
    • Mounting bolts/nuts and shim,if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inchlbs. (8.5 Nm) for 6.5L engines. For 6.6L engines tighten the starterbolts to 58 ft. lbs. (78 Nm).
    • Turbocharger exhaust pipe, on 6.6L engines
    • Right front fender splash shield and wheel, on 6.6L engines
    • Negative battery cables

Jul 30, 2008 | 2002 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...