Question about Cars & Trucks

1 Answer

I lost pressure to clutch and now makes a terrible noise and will only go into forward gears

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,623 Answers

Make , model , year and vehicle would be a help in getting a close answer
but at this point take it to man accredited clutch and brake shop for a diagnosis and quote
most likely will not be a clutch problem but a hydraulic or cable failure

Posted on Apr 29, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Going into first gear making noise


Defective clutch pressure plate release bearing is the only thing that can give this noise.

Dec 07, 2012 | Cars & Trucks

2 Answers

Squealing noise stops when i push in clutch pedal we were on the interstate and suddenly i had no clutch pedal we got off the street it was hard to get it out of gear i checked the fluid it was fine...


Sounds like a bad Throw Out Bearing.. Needless to say.. it has to be repaired.

Depending on mileage.. may as well replace the clutch/pressure plate.. and have he flywheel looked at.. change the tranny oil.. check the u joints.. rear end etc..

Best of luck!

Apr 09, 2011 | 1997 Chevrolet Camaro

3 Answers

Fiesta started making noises either gearbox or clutch? clunks going in to reverse, shudders driving off in 1st gear


sounds like your clutch is going out, is it hard to put in gear with clutch all the way depressed? could also be the sinkronyzer going out, could be the gears in the transmission also going bad. need to check the fluid in the transmission.

Feb 11, 2011 | Ford Fiesta Cars & Trucks

1 Answer

Peugeot 206 NEW clutch pressure and clutch plates were replaced including the bearing. Clutch is making a rattling noise but not when pedal is down. Having difficulty getting into 1st and 2nd gears....


its likley to be the clutch center plate cush springs are loos and the center plate is warped so wnen you try to get into gear the clutch is draging the gear box around,,,bipping the clutch stops the clutch spinning so no noise! all you can do is strip the lot down again and fine the fault and fix it

Feb 08, 2010 | 1987 Peugeot Liberte

1 Answer

Hi, peugeot 206 clutch/engine problem..


It seems like the clutch pressure plate has given in. Best would be to replace the clutch pro-kit.( Clutch pressure plate, clutch plate and release bearing)

Sep 03, 2009 | 2005 Peugeot 405

3 Answers

When put into drive the car won't drive


the problem is the forward clutch pack has failed in the trans or the hydraulic pressure that applies that clutch pack is leaking. u are going to need an overhaul

Jul 20, 2009 | 2000 Ford Explorer

1 Answer

My 2001 lincoln ls wont go into 4th or 5th gears. Took it to a trans shop and they recommended a rebuild for 3000+ dollars. But Ive been reading that alot of lincolns with the same problem getting err


call your dealer to get an estimate too.

Shift Patterns Upshifts
Transmission upshifting is controlled by the powertrain control module. The PCM receives inputs from various engine or vehicle sensors and driver demands to control shift scheduling, shift feel and torque converter clutch (TCC) operation.
The PCM has an adaptive learn strategy to electronically control the transmission which will automatically adjust the shift feel. When the battery has been disconnected, or a new battery installed certain transmission operating parameters may be lost. The Powertrain Control Module (PCM) must re-learn these parameters. During this learning process you may experience slightly firm shifts, delayed, or early shifts. This operation is considered normal and will not affect the function of the transmission. Normal operation will return once these parameters are stored by the PCM.
---------------------------------------------------------------------
Apply Components Band — Overdrive
For component location, refer to Disassembled Views in this section.
During 2nd and 5th gear operation, hydraulic pressure is applied to the overdrive servo.
  • This pressure causes the piston to move and apply force to the band.
  • This action causes the overdrive band to hold the overdrive drum.
  • This causes the overdrive sun gear to be held stationary through the adapter plate and the overdrive drum.
Band — Low/Reverse
For component location, refer to Disassembled Views in this section.
During 2nd gear operation, 1st gear operation and reverse, hydraulic pressure is applied to the low/reverse servo.
  • This pressure causes the servo to move and apply force to the low/reverse band.
  • This action causes the low/reverse brake drum to be held.
  • This action causes the low/reverse planetary assembly to be held stationary.
Band — Intermediate
For component location, refer to Disassembled Views in this section.
During 3rd gear operation, hydraulic pressure is applied to the intermediate servo.
  • This pressure causes the servo to move and apply force to the intermediate band.
  • This action causes the direct clutch drum to be held.
  • The intermediate band holds the intermediate brake and direct clutch drum to the case in 3rd gear.
  • This causes the input shell and forward sun gear to be held stationary.
Clutches — Direct
For component location, refer to Disassembled Views in this section.
The direct clutch is a multi-disc clutch made up of steel and friction plates.
  • The direct clutch is applied with hydraulic pressure and disengaged by return springs and the exhaust of the hydraulic pressure.
  • It is housed in the direct clutch drum.
  • During 4th, 5th, and reverse gear application, the direct clutch is applied transferring torque from the forward clutch cylinder to the direct clutch drum.
  • This action causes the forward sun gear to drive the pinions of the low/reverse planetary carrier.
Clutches — Forward
For component location, refer to Disassembled Views in this section.
The forward clutch is a multi-disc clutch made up of steel and friction plates.
  • The forward clutch is applied with hydraulic pressure and disengaged by return springs and the exhaust of the hydraulic pressure.
  • The forward clutch is applied in all forward gears.
  • When applied, the forward clutch provides a direct mechanical coupling between the center shaft and the forward ring gear and hub.
Clutches — Coast
For component location, refer to Disassembled Views in this section.
The coast clutch is a multi-disc clutch made up of steel and friction plates.
  • The coast clutch is applied with hydraulic pressure and disengaged by return springs and the exhaust of the hydraulic pressure.
  • The coast clutch is housed in the overdrive drum.
  • The coast clutch is applied when in 1st, 3rd, D4, and reverse positions.
  • When applied, the coast clutch locks the overdrive sun gear to the overdrive planetary carrier, thus preventing the one-way clutch from overrunning when the vehicle is coasting.
    • This allows the use of engine compression to help slow the vehicle and provide engine braking.
Clutches — Intermediate
For component location, refer to Disassembled Views in this section.
The intermediate clutch is a multi-disc stationary clutch made up of steel and friction plates which are in a module assembly that includes the cylinder and frictions.
  • Applied with hydraulic pressure.
  • Disengaged by a return spring and releasing of hydraulic pressure.
  • Hydraulic pressure is feed through a feed tube in the case worm trail.
  • Uses a bonded piston in an aluminum housing.
  • Applied in during a 2-3 shift event.
  • Transfers torque from the sun gear to the planetary carrier.
  • Torque transfer causes the one way clutch to engage and holds the sun gear from turning, delivering 3rd gear.
One-Way Clutch — Direct
For component location, refer to Disassembled Views in this section.
The direct one-way clutch is a sprag-type one-way clutch that is pressed into the center shaft.
  • The direct one-way clutch is driven by the ring gear of the overdrive planetary carrier.
  • The direct one-way clutch holds and drives the outer splines of the center shaft in 1st, 3rd, 4th and reverse gears.
  • The direct one-way clutch overruns during all coast operations and at all times in 2nd and 5th gear.
One-Way Clutch — Intermediate
For component location, refer to Disassembled Views in this section.
The Intermediate One-Way Clutch is a sprag type one-way clutch.
  • The Intermediate One-Way Clutch connects the intermediate assembly to the input shell and sun gear assembly in third gear.
One-Way Clutch — Low/Reverse
For component location, refer to Disassembled Views in this section.
The low/reverse one-way clutch is a sprag type one-way clutch.
  • The low/reverse one-way clutch holds the low/reverse drum and low/reverse planetary assembly to the case in 1st and 2nd gear.
  • In all other gears the low/reverse one-way clutch overruns.
------------------------------------------------------------------------------

May 01, 2009 | 2002 Lincoln LS

1 Answer

Transmission?


hi, the problem your having sounds like the thrust bearing that pushes the clutch on and off has started to colapse you can buy these thrust bearings on their own but as you have to take the gearbox off its best to replace the clutch and pressure plate as well.

If you buy a clutch kit you will get the clutch and the pressure plate and also the thrust bearing they are all easy to replace but the hard part is removing the gearbox for this you will need two people as it is heavy and can be hard to line back up when putting the gearbox back onto the spline.
You will also need to buy a clutch alligning tool witch keeps the clutch dead center whilst you are tightening up the pressure plate.
If you are unsure what you are doing then leave it to a pro but if you are going to do the repair yourself then make sure you get some cleaning fluid like alcohol based cleaner as the pressure plate has an oil on it so as to stop it rusting whilst its on the shelf in the car spares shop.

Let me know if you have any questions and ill be glad to assist you further ok

May 27, 2008 | 1994 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...