Question about Nissan Cars & Trucks

Open Question

Seal size between propshaft gearbox nissan 3.3v6

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan D22 3.0L diesel 4x4 - clutch shudder.


The most common cause of clutch judder when releasing to pull away is oil on the plates. That can be caused by main bearing seals failing.

Apr 19, 2017 | Nissan Cars & Trucks

1 Answer

Steps to removing a transmission from a GMC ENVOY 2004 V6, 4WD.


Park the vehicle in a clean dry well lit place. Work with safety in mind. Its always good to take pictures as you strip the/ a assembly. Refer back to pictures if you get stuck. Dis-connect the battery. Remove the gear linkages and speedo-drive and power cables from the gearbox. Remove the starter motor. Loosen the propshaft. Mark the yokes of the propshaft- for upon installation to avoid an unbalanced propshaft. Loosen the centre bearing. Remove the propshaft. Remove the cross member underneath the gearbox if there is one. Loosen bolts around the gearbox to cylinder block. Use a gearbox jack to support the gearbox. Take the bolts out from the gearbox to cylinder block. Pull gearbox backwards. Lower the gearbox. This is pretty much the standard way of removing gearbox. Note, there might be a transfer box, normally with 2 propshafts. Mark the yokes. Remove propshafts, transfer box and then gearbox. Remember to always work safe.

Dec 19, 2014 | Cars & Trucks

1 Answer

I have a nissan 1400 champ and is leaking oil on the front part of the manual 5 speed gearbox and the rear part of the gearbox. I have replaced the crankshaft oil seal but i still have oil leaking on


There are seals on the front and rear of the transmission. If the clutch wasn't covered in engine oil, then replacing the crankshaft seal wasn't necessary. Reseal the transmission.

Sep 29, 2014 | Nissan Cars & Trucks

1 Answer

Can i remove my 2004 santafe outomatic propshaft and drive without it


the prop shaft is what transfers drive from gearbox to the axle and then the wheels so removing it would be a ridiculous thing to do as vehicle would'nt be able to move !!!!!!!!!!!!!

Apr 28, 2014 | Hyundai Santa Fe Cars & Trucks

1 Answer

Hi my name is frik I have a oil leak on front and


you will have to removhe the gearbox, while you are at it check for bearing play, and it is a good time for replace the fluid and chaeck for filings

Jul 19, 2010 | 1990 Nissan Hardbody King Cab

2 Answers

Loud noise when put into drive


If it is one big clunk then it might just be the universal joint that connects the drive shaft to the rear end. It is very dangerous to drive a vehicle with bad U-joints. If they break the whole drive shaft falls out. If the front u joint breaks it can act like a pole vault for your vehicle.

May 29, 2010 | 2000 Jeep Grand Cherokee

2 Answers

1994 nissan quest crankshaft rear main seal removal


u don't have to remove the engine however you must remove the transmission and flywheel, you will also need the Nissan special tool to install the new full circle seal or it will leak.

Jul 28, 2009 | 1994 Nissan Quest

1 Answer

Propshaft noise


Propeller (or driveshaft) will transmit noise check the joints at both ends for binding or rust (best done with it out of the car)

Jun 07, 2009 | 2006 Nissan Pathfinder

1 Answer

GEARBOX REMOVAL


Hi you need to remove x member, engine cradle,propshaft etc to remove gearbox just in the middle of doing one myself.

Jun 08, 2008 | 2003 Toyota RAV4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...