Question about Cars & Trucks

Open Question

How do l remove the top hob cover (enamel) on a new world vision 55hlg to replace the fascia.there are 2 screws each side which l've undone but there is still something holding it.mode

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: How do I replace brake light bulHbs?

There are two more on the inner wall of your tailgate

Posted on Aug 12, 2008

Ad
  • 1 Answer

SOURCE: replace rear turn signal bulb on 2007 H3 - driver side

1st::Unscrew the 2 screws that hold the light in.
2nd::Slide your hand behind the light and pull the light towards you. Make sure that you pull it straight, as if the h3 was driving away from you, so you dont break the two pins that are holding the light in...PULL ONE PIN AT A TIME!!!

Dont pull it to far away from the hummer as there are wires attached that need to stay attached.

3rd::turn the back of the bulb to unlock it from the lens...
4th:: slide the bulb out and remove thebulb by pulling it straight out.
5th::put the new bulb in, lock it back into the lens, then insert it back where you got it from,...

MAKE SURE you move the wires out of the way when you put the lens back in...they will get in the way and can be damaged.

Posted on Apr 07, 2009

  • 1 Answer

SOURCE: Fitting brake light - fiesta zetec

There is also a push in socket at the top of the light and a clip at the bottom. When the screws are all undone insert a flat screw driver under the light fitting about 4 inches from the top (remember to use a cloth under the edge of the screwdriver to avoid marking the paintwork) you should be able to push it out now.

Posted on May 02, 2009

  • 1 Answer

SOURCE: 2005 odyssey tail light bulb replacement,how to do

There is a little connector to the front of the lense assembly, you will need to pop that out... Carefully use a screwdriver to accomplish this...86f2b5d.jpg
You can see the white plug of the connector below

4cc118a.jpg

Posted on Jun 20, 2009

  • 1 Answer

SOURCE: replacing side view mirror cover on 200 SAAB 9-5

I need a complete passenger Side Mirror (2nd Hand) N-95 (S Reg) contact 07966 366195

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change headlight bulb drivers side 2011 Chevrolet malibu


Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary.
Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
Remove 2 headlamp screws.
Pull forward on the outside edge of the headlamp in order to release the up and down Locator tabs on the backside of the headlamp.
Pull forward on the top Inside edge of the headlamp to release the inboard up and down Locator.
Pull the headlamp assembly down.
Pull the headlamp assembly forward far enough to access the electrical connection.

Mar 23, 2015 | 2011 Chevrolet Malibu

1 Answer

How do I get the fascia off to change from Singel din to dubble din on Kia Sportage 2006


A Chilton/Haynes repair manual that covers this vehicle has an entire section on interior fascias/trims and how to remove them and maintain them. As well as the information for general repair and maintenance.

Dec 13, 2014 | 2006 Kia Sportage

1 Answer

How do I replace my rear bumper on my 04 pacifica


  1. Open liftgate.

133387935 Fig. 12

  1. Remove two push pin fasteners per side at the liftgate tower area (Fig. 12).
  2. Hoist and support vehicle with safety stands, as necessary.

133387936 Fig. 13

  1. Disconnect the park assist wire connector under the vehicle and the push pin fasteners attaching wire harness under the vehicle (Fig. 13)
  2. Remove the four push pin fasteners attaching rear fascia to reinforcement bumper.
  3. Remove two screws (each side) attaching fascia to rear fascia bracket in the wheelhouse.
  4. Remove the screw on each side attaching the upper fascia in the tail lamp bucket area.
  5. Remove rear fascia from vehicle by lifting sides of fascia up and outboard to release from rear fascia brackets.
  6. Place fascia on a clean surface.

133387937 Fig. 14

  1. Remove park assist sensors, if necessary (Fig. 14).

133387938 Fig. 15

  1. Remove spring clips attaching upper and lower fascia together (Fig. 15).
  2. Using a trim stick release locking tabs and separate the upper and lower fascia.

133387939 Fig. 16
133387940 Fig. 17

  1. Remove move the bright chrome molding from the upper fascia (Fig. 16). Using a trim stick, starting at the out edge of the fascia release the locking tabs (Fig. 17). Grip the molding and pull outward from the fascia while releasing the locking tabs.
  2. Remove molding from fascia.
INSTALLATION

  1. Place bright chrome molding in position on the upper fascia.

133387941 Here you go1_9_2012_2_48_31_am.gif

Jan 06, 2012 | 2004 Chrysler Pacifica

1 Answer

Remove dash on 2002 chevy tracker and remove factory stereo and install new one


Glad I didn't read this page before I replaced my stereo.

Remove stereo fascia with three screws - 1 at the top, two on each side of ash tray. Remove 4 screws holding in stereo. Done - takes about 3 minutes.

Oct 29, 2011 | 2002 Chevrolet Tracker

1 Answer

How to remove the rear bumper cover on a pontiac 2004 grand prix


  1. Open the trunk.
  2. Remove the rear compartment sill plate. (Trim round the back edge of the trunk)
  3. Pull the left and right compartment side trim panels down to access the fascia bolts and nuts.
  4. Remove the tail lamps.
  5. Remove the fascia bolts and nuts from the rear bumper fascia 1 nut 1 bolt on each side near tail lights.
  6. Remove the push-in retainers from the top edge of the fascia.(4 plastic circles, pull up on center of cirle with screwdriver
  7. Raise and support the vehicle.
  8. From underneath Remove the push-in retainers from the rear bumper fascia (one on each side I think)
  9. Remove the fascia bolts from the rear bumper fascia. on on each side from, up where the facia connects to the quater panel)
  10. Remove the rear bumper fascia from the vehicle

Apr 14, 2011 | 2004 Pontiac Grand Prix

1 Answer

Two questions how do you change a low beam lightbulb in a cadillac srx 2005 and why in early morning starts does the same car hesitate to pull away?


1. Remove front wheel well front half splash guard, each side. There are about 2 screws and the guard pulls forward to seperate from the rear half.
2. After removing the splash guard, you can access one screw that attaches the front fascia, each side.
3. Then about 6 plastic push pin type screws along the bottom, underneath.
4. About 5 push pin type screws on the top.
5. Fascia should then simply pull forward. It is a bit bulky and an extra pair of hands is helpful.
6. Then there are 3 screws to remove the headlamp assembly. Unclip the wiring harness.
7. Then 4 screws to remove the bulb access cover plate.

Dec 24, 2010 | 2005 Cadillac SRX

1 Answer

Cracked fascia of dashboard


Clarification of the would be greatly appreciated. However the entire dash is held on with about 10-15 screws.
Open both doors and pop off the platic covers normally hiden when the doors are closed. Remove the screws from both sides here.
Then open the glove box. There are 2 screws that hold on a metal bracket, remove them.
On the top-middle of the dash there is a vent to defrost your windshield.One screw holds it on, remove it (phillips I believe).Then remove the screws under the vent so that the dash can be completly removed.
The top part of the dash a 5" strip closest the to windshield will have to be removed frist. By simply pulling it up from the sides.
The entire dash can then be removed fairly easy by pulling it apart from the housing for the odometer and across the entire dash.
The housing that is around your odometer can then be removed by simply removing a few screws across the top and under the radio. You will have to disconnect the wireing harness for the light adjuster left of the blinker on the dash. to remove this part. (I had a little trouble getting this out so I had to take apart the plastic housing for the ignition. 3 bolts slightly bigger then the ones on the dash under neath.)

Jan 10, 2010 | 2005 Chevrolet Cavalier

3 Answers

How do i get to the head light on my 2008yukon denali with out pulling air filter box out and windshild washer out


This is a rather difficult task to perform as the complete headlamp must be removed to do so. Here is what you will need to do to access the bulb. Feel free to contact me with any questions! Good luck.

  • Remove the 2 forward wheelhouse liner screws.
  • Remove the 2 washer container push pins.
  • Open the hood.
  • Remove the 6 upper fascia bolts right to the hood latch mechanism.
  • Remove the lower rear fascia bolt from the support bracket.
  • Loosen the 2 fascia to fender bolts from under the fascia.
  • Pull the outboard end of the front fascia straight outboard until it disengages from the fender attachment bracket.
  • Pull the fascia forward and downward to allow enough clearance to remove the headlamp assembly.
  • Loosen the lower outboard attachment bolts.
  • Remove the 2 upper headlamp bolts.
  • Grasp the headlamp at the upper inboard and lower outboard side and pull the headlamp forward to disengage the locating tab.
  • Pull the outboard side of the headlamp forward until the 2 locating pins disengage from the radiator support.
  • Disconnect the forward lamp harness connector.
  • Dec 07, 2009 | 2008 GMC Yukon Denali

    1 Answer

    I need info on how to replace the headlamp bulbs on my 2008 Chevy Malibu, can you help.


    The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.
    1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
    2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
    3. You will also need to remove some of the fasteners at the front of the inner wheel well.
    4. The Front Bumper Fascia is the plastic cover over your front bumper.
    5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.

    Oct 27, 2009 | 2008 Chevrolet Malibu

    4 Answers

    Where is the flasher on a 1994 toyota previa


    The flasher is bolted to the firewall behind the right side of the instrument panel and you can't get to it from underneath the instrument panel. You will have to remove the center console fascia to get to the instrument cover screws and remove the instrument cover. Then you can get to the instrument holding screws and move the instrument panel out of the way. Either a service manual or AutoZone.com will have this information and pictures. Replace the flasher with a genuine Toyota flasher relay. The aftermarket relays might look like they fit but I have found out they don't work properly. The flasher is bolted to the firewall with a 13mm bolt. Take out the bolt and replace the flasher.

    Jul 15, 2009 | 1997 Toyota Previa

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    18 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...