Question about GMC Sonoma

Open Question

2003 GMC SONOMA

REPLACE DRIVE BELT WITH OUT AC PUMP

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: 1996 GMC Sonoma heater core

the dash has to come out

Posted on Sep 11, 2008

  • 366 Answers

SOURCE: how do you replace a headlight on a 1995 gmc sonoma?

theres 2 black headlight retainers that u pull up from inside under hood compartment,headlight housing will come out and bulbs will be accessible.

Posted on May 28, 2009

  • 11 Answers

SOURCE: drain and replace power steering fluid in my gmc

generally there is 2 hose going to the reservior , usually the small one it the inlet, take that off anbd put a blocked off hose in place. put into a bucket, have a few liters handy turn the car on and have some1 fill it keeping it full, warning it will come out fast. and have some1 turning the steering wheel lock to lock. untill clean, the turn car off

Posted on Jul 11, 2009

c17hydro
  • 2984 Answers

SOURCE: HOW TO CHANGE DRIVE BELT ON MY 98 GMC SONOMA 4

it may be easier to attach the breaker bar to the tensioner arm from under the vehicle to relieve belt tension

a281459.gif
a35a276.gif

  1. On 1994-97 2.2L engines and 1994-96 4.3L engines, using a 1/2 in. breaker bar and if necessary, with a socket placed on the tensioner pulley bolt, rotate the tensioner counterclockwise to relieve the belt tension. On some 2.2L engines it may be easier to attach the breaker bar to the tensioner arm from under the vehicle.
  2. On 1998-99 2.2L engines and 1997-99 4.3L engines, using a 3/8 in. breaker bar, rotate the tensioner counterclockwise to relieve the belt tension. On some 2.2L engines it may be easier to attach the breaker bar to the tensioner arm from under the vehicle.
  3. Remove the serpentine belt.
To install:
  1. Route the belt over all the pulleys except the tensioner.
  2. Place the breaker bar and if necessary the socket, on the tensioner pulley bolt and rotate the tensioner counterclockwise to the released position.
  3. Install the belt and return the pulley slowly to its original position. Do not let the pulley snap back into position as this may damage the belt and pulley.
  4. Check that the belt is properly seated in each pulley.

Posted on Oct 11, 2009

SOURCE: How do you replace the rear u joint on a 99' gmc

Mark the driveshaft and yoke in a manner that will allow you to reassemble it in the same orientation that it's in now. This is done to avoid driveline vibrations. Next remove the 4 7/16" head bolts on the driveshaft yoke. Use a lone screw driver or pry bar to pop the driveshaft off the yoke and slide the other end out of the transmission. Using a u-joint tool press out the old u-joint and press in the new one. You could bring this to a machine shop or a mechanic and have them do it for you if you don't have the correct tools. I think autozone may rent a ball joint press out for free. Next reassemble it orientated the same way you took it off.

Posted on Dec 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the crank shaft pulley on a 1998 GMC sonoma 4.3 liter


drain and remove the radiator and the drive belt, also the fan and use a steering wheel pulley tool

Sep 20, 2014 | 1998 GMC Sonoma

1 Answer

2003 sonoma shuts down when MAP sensor is plugged in


Could be a bad one even if its new it happens

Feb 25, 2014 | 2003 GMC Sonoma

1 Answer

03 gmc sonoma ,ran out of gas ,put in fuel,but know I start it ,wont start is it the fuel pump


yes it is probably fuel pump which is located in the gas tank. gas keeps pump from overheating. never let fuel level get too low in tank...

Jun 25, 2012 | 2003 GMC Sonoma Extended Cab

1 Answer

SERPINTINE BELT ON 95 GMC SONOMA AC 2.2 NEED DIAGRAM HOW IT GOES ON. THANKYOU


Is the belt diagram sticker still on the top of the cross brace where the radiator is or on the inside of the hood?

Jan 18, 2011 | 1995 GMC Sonoma

2 Answers

How do I route a surpentine belt on a 1999 GMC with a V6 and AC?


If you buy your belt from Autozone,the belt routing is on the package

Dec 19, 2009 | 1999 GMC Sonoma

1 Answer

1998 gmc sonoma air conditioner - not cold


Check the magnetic clutch is engaged on front of a/c pump, have the motor running, a/c on and fan on high, if the centre hub is static the pump in not switched on, this can happen when the gas pressure gets low.

Aug 05, 2009 | 1998 GMC Sonoma

1 Answer

Need to replace water pump in a 1995 GMC Sonoma


Hi there:

Ok 8th digit is a 4, that means you have a 2.2L engine. you will find your water pump located on the drivers side of the block just below the cylinder head. It is driven by a belt so it has a pully on the front of it that kind of hides it. there is no hoses attached to it as it pumps the coolant through the block.

Hope this helps.
Farrout!

Mar 17, 2009 | 1995 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...