Question about Cars & Trucks

Open Question

My steering wheel won't lock on my 1988 Chevy Beretta

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 69 Answers

SOURCE: ignition key won t turn. steering wheel locked

the key may be worn badly or the ignition needs to be replaced.

Posted on Jul 31, 2009

Ad
  • 564 Answers

SOURCE: Howa to replace wiper switch on 1988 Chevy

u need a tool to suppress the metal ring cover & then pull have moon clip out,,then the melal ring comes off then the rest;;;

Posted on Jan 31, 2010

tripletauto
  • 1450 Answers

SOURCE: 1986 chevy c10 truck. pulled steering wheel to

THE horn piece should turn with the wheel lock plate. if it does not then something is not installed properly

Posted on Apr 12, 2010

  • 2 Answers

SOURCE: 1988 Beretta: location fuel pump relay 1988 beretta...

1st relay on fire wall next to brake booster

Posted on Aug 18, 2010

junkman1249
  • 552 Answers

SOURCE: steering wheel is locked on my 95 ford f150 xl..it starts and goes into gear but the steering wheel won't move..it is locked

you can break the lock by pulling down on the steering whell very hard. or if your ignitons swith is bad you have to get a new one

Posted on Dec 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuel pump fuse located on 1988 chevy beretta


There are 2 Fuse Panels, one inside the Engine Compartment and one on the Drivers Side under the dash.

Nov 07, 2014 | 1988 Chevrolet Beretta

1 Answer

Firing order Chevy 2.8


Hi there:
1988 Chevrolet Beretta 2.8 liter V-6 VIN "W"


12_20_2011_6_36_54_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Nov 20, 2011 | 1988 Chevrolet Beretta

1 Answer

I have a unique problem: the ignition switch in my son's 1989 Beretta now turns freely when you insert the key. We bought a new ignition, and were removing the steering wheel when he got a screw stuck in...


You can bypass the old system and install a lock and ignition switch like the old cars w/o locking steering. It's not a good idea. I would think about asking a locksmith to help or replace the steering column.

Mar 18, 2011 | 1989 Chevrolet Beretta

1 Answer

1988 chevy truck w/tilt steering column need disassembly instructions or diagram to replace muti function wiper switch


This can be found in the Hanes repair manual that you can get at any auto parts store, Auto Zone, step by step with photos. Not a hard job but you will new a steering wheel puller to get the lock ring out and the wheel off.

Feb 19, 2011 | 1988 Chevrolet C1500

1 Answer

How do I remove a ignition cylinder on a 1991 Chevy Beretta?


Remove sterring wheel and work your way to the cylinder. Special tools required ,so make sure you have them..steering wheel puller. lock plate remove tool. Also if it has cruise be careful when you pull turn lever, so the wires dont break. Also you need to unfasten the wires at bottom of collum so they will pull back far enough to give more access

Feb 17, 2011 | Chevrolet Beretta Cars & Trucks

1 Answer

Where do i find the turn signal flashers for a 1994 chevy beretta?


GM Corsica/Beretta 1988-1996 Repair Guide

The turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Hope helped (remember rated this help) Good luck.

Oct 30, 2009 | Chevrolet Beretta Cars & Trucks

1 Answer

How do you replace a igntion lock cylinder


if u looking to replace the cyl. and key
first remove the steering wheel,that will give u access
to your cyl.

G

May 18, 2009 | 1988 Chevrolet Nova

1 Answer

I have a 1988 chevy beretta and my turn signals and brake lights are not working i checked all the fuses and they all seem to be good. what could be the problem?


But make sure the hazard switch (4 ways) is completely OFF Have you been having any lighting problems for a while that you have been neglecting?
Contact me if you still Have any questions If you have a tilt wheel try moving it to another position sometimes the wires get worn because they FLEX a lot if someone always uses the tilt you can have a broke wire, the brake lights circuit runs THROUGH the turn signal switch inside the steering column.

Aug 03, 2008 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...