Question about Cars & Trucks

1 Answer

How do I get the valve and how much - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 832 Answers

What valve

Posted on Apr 28, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is a egr valve


  1. Install a tachometer on the engine, following the manufacturer's instructions.
  2. Detach the engine wiring harness connector from the Idle Air Control (IAC) solenoid.
  3. Disconnect and plug the vacuum supply hose from the EGR valve.
  4. Start the engine, then apply the parking brake, block the rear wheels and position the transmission in Neutral.
  5. Observe and note the idle speed.
If the engine will not idle with the IAC solenoid disconnected, provide an air bypass to the engine by slightly opening the throttle plate or by creating an intake vacuum leak. Do not allow the idle speed to exceed typical idle rpm.
Using a hand-held vacuum pump, slowly apply 5-10 in. Hg (17-34 kPa) of vacuum to the EGR valve nipple.
  1. If the idle speed drops more than 100 rpm with the vacuum applied and returns to normal after the vacuum is removed, the EGR valve is OK.
  2. If the idle speed does not drop more than 100 rpm with the vacuum applied and return to normal after the vacuum is removed, inspect the EGR valve for a blockage; clean it if a blockage is found. Replace the EGR valve if no blockage is found, or if cleaning the valve does not remedy the malfunction.


EGR Valve Removal & Install
3.0L OHV (2 valve) and 3.4L SHO engines

b9175c5.jpg

Fig. : EGR mounting-3.0L OHV (2 valve) engine

5fcd84e.jpg

Fig. : EGR mounting-3.4L (SHO) engine

4552fc2.jpg

Fig. : Remove the two retaining bolts and...

b849310.jpg

Fig.: ... remove the valve from the intake manifold

795549d.jpg

Fig.: Thoroughly clean the mating surfaces of the manifold and the EGR valve (if being reused)
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hose from the EGR valve.
  3. Using a 22mm wrench or crowfoot, disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
  5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 26-47 ft. lbs. (35-65 Nm).
  3. Connect the vacuum hose to the EGR valve.
  4. Connect the negative battery cable.

3.0L OHC (4 valve)

d8a563e.jpg

Fig. : EGR mounting-3.0L OHC (4 valve) engine
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hose from the EGR valve.
  3. Remove the two EGR tube-to-EGR valve retaining nuts.
  4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
  5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
  2. Connect the EGR valve-to-EGR tube, then tighten the retaining nuts.
  3. Connect the vacuum hose to the EGR valve.
  4. Connect the negative battery cable.

Tell us news.

Oct 12, 2012 | 1998 Nissan Maxima

1 Answer

Quest code p1136


P1136 NISSAN - Intake Valve Timing Control Solenoid Valve Circuit Bank 2
Possible causes- Intake valve timing control solenoid valve bank 2 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 2 circuit connectors
- Intake valve timing control solenoid valve bank 2 Tech notes Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.

Aug 29, 2012 | 2005 Nissan Quest

2 Answers

Valve clearance 4g13


make the engine runs for about 30minutes before adjusting the valves,
valve clearances:
intake valve = 0.20mm(0.008 in)
exhaust valve = 0.25mm(0.010 in)
for reference only when the engine is cold,
valve clearances:
intake valve = 0.25mm(0.010 in)
exhaust valve = 0.30mm(0.012 in)
engine specs: mitsubishi 4g13 1.3L (if you have same engine)

Feb 29, 2012 | Mitsubishi Cars & Trucks

1 Answer

Feul will burp mout of the filler cap no mater how slow I fill the car and the service engine soon light is on, how do I change the feul tank filler vent check valve?


Hi, your EVAP vent valve is likely stuck closed. The valve is under the car near the fuel tank. Remove the valve and check to see if it's stuck. You may be able to restore operation by cleaning the valve with carb cleaner. The valve should be open when no voltage is applied. I have pasted instructions below from autozone.com. Please let me know if you have any questions, and thanks for using FixYa.
jturcotte_1546.gif Vent Solenoid Valve
2.2L & 2.4L Engines

  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.

To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Apr 18, 2011 | 2004 Chevrolet Cavalier

1 Answer

Well we tried adjusting the valves and then it will start and make a werid noise and then will be about to shut off and it doesnt sound right plezz can you help me? its a 1997 gmc 5.7 1500


With the Engine in the number 1 firing position, adjust the exhaust valves for cylinders number 1, 3, 4, and 8 and the intake valves for cylinders number 1, 2, 5, and 7.
Turn the valve rocker arm nut counter clockwise until the valve lash is felt in the valve pushrod.
Turn the rocker arm nut clockwise until all of the valve lash is removed (zero valve lash).
Zero valve lash can be felt by moving the valve pushrod up and down between your thumb and forefinger until there is no more up and down movement of the valve pushrod.
When all the valve lash is removed, then turn the valve rocker arm nut clockwise 1 additional turn (360 degrees).


With the engine in the number 6 firing position, adjust the exhaust valves for cylinders number 2, 5, 6, and 7 and the intake valves for cylinders number 3, 4, 6, and 8.

Follow the same steps as above.

Apr 01, 2011 | GMC Suburban Cars & Trucks

1 Answer

I have a 2003 a4/b6 1.8 turbo and the engine light is on. The DTC codes says random misfire, misfire on cylinder #2 and #3 also, Oxygen (Lambda) Sensor Regulation: Bank 1: System too Lean : P1111. Any...


If you can supply me with all the codes your vehicle is showing, I can assist you. As far as the P1111 DTC goes I have listed the info below with some possible solutions.

P1111- Intake Valve Timing Control Solenoid Valve Circuit Bank 1

Intake valve timing control solenoid valve is activated by ON/OFF pulse duty (ratio) signals from the ECM. The intake valve timing control solenoid valve changes the oil amount and direction of flow through intake valve timing control unit or stops oil flow. The longer pulse width advances valve angle. The shorter pulse width retards valve angle. When ON and OFF pulse widths become equal, the solenoid valve stops oil pressure flow to fix the intake valve angle at the control position. The code is triggered when an improper voltage is sent to the ECM through intake valve timing control solenoid valve. Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.

Possible Causes:
- Intake valve timing control solenoid valve bank 1 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 1 circuit connectors
- Intake valve timing control solenoid valve bank 1
- Dirty Oil

Possible Solutions:
- Change Oil
- Replace Intake valve timing control solenoid valve

Jan 20, 2011 | 2003 Audi A4 Cabriolet

1 Answer

How do you get the pcv valve out of the valve cover


Usually you grasp it an pull it out.

Positive Crankcase Ventilation (PCV) Valve Removal & Installation To Remove:
PCV Valve location (3.3L & 3.8L engines shown, 2.4L similar) chry-04-33-829.gif

  1. Disconnect the vacuum hose from the positive crankcase ventilation (PVC) valve.
  2. Remove the positive crankcase ventilation valve from the valve cover.
To Install:
  1. Install the positive crankcase ventilation valve in the valve cover.
  2. Connect the vacuum hose to the positive crankcase ventilation valve.
prev.gif next.gif

Jan 16, 2011 | 2006 Dodge Grand Caravan

1 Answer

How do you change the pvc valve


Not sure on your engine so heres both types. :-) Hope it helps. Cobra
Positive Crankcase Ventilation (PCV) Valve — 3.0L (2V) Removal and Installation
  1. Disconnect the positive crankcase ventilation (PCV) valve tube quick-connect from the PCV valve.
e8e1fc3.jpg
CAUTION: A new PCV valve must be installed if removed from the cam cover. Damage will occur to the locking mechanism on the PCV valve.
Remove the PCV valve.
  • Disconnect the PCV valve electrical connector.
  • Rotate to release and remove the PCV valve.
cb7856a.jpg


Positive Crankcase Ventilation (PCV) Valve — 3.0L (4V) Removal and Installation
  1. Disconnect the positive crankcase ventilation (PCV) valve tube from the PCV valve
0f6f63a.jpg

  • CAUTION: A new PCV valve must be installed if removed from the cam cover. Damage will occur to the locking mechanism on the PCV valve.
    Rotate to release and remove the PCV valve.

  • 26db756.jpg

  • Jun 13, 2010 | 2005 Ford Taurus

    3 Answers

    EGR Valve not working


    EGR Valve Testing
    1. Install a tachometer on the engine, following the manufacturer's instructions.
    2. Detach the engine wiring harness connector from the Idle Air Control (IAC) solenoid.
    3. Disconnect and plug the vacuum supply hose from the EGR valve.
    4. Start the engine, then apply the parking brake, block the rear wheels and position the transmission in Neutral.
    5. Observe and note the idle speed.
    If the engine will not idle with the IAC solenoid disconnected, provide an air bypass to the engine by slightly opening the throttle plate or by creating an intake vacuum leak. Do not allow the idle speed to exceed typical idle rpm.
    Using a hand-held vacuum pump, slowly apply 5-10 in. Hg (17-34 kPa) of vacuum to the EGR valve nipple.
    1. If the idle speed drops more than 100 rpm with the vacuum applied and returns to normal after the vacuum is removed, the EGR valve is OK.
    2. If the idle speed does not drop more than 100 rpm with the vacuum applied and return to normal after the vacuum is removed, inspect the EGR valve for a blockage; clean it if a blockage is found. Replace the EGR valve if no blockage is found, or if cleaning the valve does not remedy the malfunction.


    EGR Valve Removal & Install
    3.0L OHV (2 valve) and 3.4L SHO engines

    b9175c5.jpg

    Fig. : EGR mounting-3.0L OHV (2 valve) engine

    5fcd84e.jpg

    Fig. : EGR mounting-3.4L (SHO) engine

    4552fc2.jpg

    Fig. : Remove the two retaining bolts and...

    b849310.jpg

    Fig.: ... remove the valve from the intake manifold

    795549d.jpg

    Fig.: Thoroughly clean the mating surfaces of the manifold and the EGR valve (if being reused)
    1. Disconnect the negative battery cable.
    2. Remove the vacuum hose from the EGR valve.
    3. Using a 22mm wrench or crowfoot, disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
    4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
    5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
    To install:
    1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
    2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 26-47 ft. lbs. (35-65 Nm).
    3. Connect the vacuum hose to the EGR valve.
    4. Connect the negative battery cable.

    3.0L OHC (4 valve)

    d8a563e.jpg

    Fig. : EGR mounting-3.0L OHC (4 valve) engine
    1. Disconnect the negative battery cable.
    2. Remove the vacuum hose from the EGR valve.
    3. Remove the two EGR tube-to-EGR valve retaining nuts.
    4. Remove the EGR valve mounting fasteners, then separate the valve from the intake manifold.
    5. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
    To install:
    1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm).
    2. Connect the EGR valve-to-EGR tube, then tighten the retaining nuts.
    3. Connect the vacuum hose to the EGR valve.
    4. Connect the negative battery cable.

    Tell us news.

    May 04, 2010 | 1999 Mercury Sable

    1 Answer

    How do i adjust the valves in a ford 1997tarus with a 3.0 ohv


    Valve Stem to Guide Clearance · Intake
    0.026-0.071 mm (0.001-0.0028 in) · Exhaust
    0.038-0.083 mm (0.0015-0.0033 in) Valve Clearance
    1. With No. 1 piston (6108) on top dead center (TDC) at the end of compression stroke (Position No. 1 in the illustration), check the following valves:
      Position 1
      No. 1 exhaust valve (6505) No. 1 intake valve (6507).
      No. 3 exhaust valve No. 2 intake valve.
      No. 6 exhaust valve No. 4 intake valve.
    1. Rotate crankshaft (6303) 360 degrees to position No. 2 and check the following valves:
      Position 2
      No. 2 exhaust valve No. 3 intake valve.
      No. 4 exhaust valve No. 5 intake valve.
      No. 5 exhaust valve No. 6 intake valve. 4cb038f.gif

    Oct 19, 2009 | 1997 Ford Taurus

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    18 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...