Question about 2014 Buick Verano

Open Question

Where is the camshaft position sensor in a 2014 buick verano

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: Crankshaft Position Sensor and Camshaft Position Sensor

REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Posted on Jun 02, 2009

Ad
messstat
  • 365 Answers

SOURCE: I have a 2000 buick lesabre. The fix engine soon

It NEVER was the camshaft sensor! Unless, you've removed the engine lately, which I doubt.
RUN to Advance Auto Parts and buy a can of "SeaFoam" and add to your gas tank per instructions...drive at least 100 miles and the problem should go away...IF it doesn't you'll have to replace the O2 sensors in the exhaust system...Any good mechanic should be able to do this for much less $$ than the dealership DO NOT go to the dealer for repairs!
Good Luck

Posted on Jun 22, 2009

localwonder
  • 6784 Answers

SOURCE: where is camshaft position sensor located on 3.1l

HI. Your CMP will be located, just below the cam cover gasket rail, in front of the cam carrier.

Posted on Dec 15, 2009

  • 7353 Answers

SOURCE: i need to change the camshaft position sensor for

well I dont know that car, but if you know where the camshaft is (middle of the engine) look where the front cam gear is. Its got to pick up a signal from the gear/magnet.

Posted on Jul 02, 2010

2strokeJim
  • 577 Answers

SOURCE: 2012 buick verano transmission lag

Tell dealer to do a trans flush with a TECH II and reset the trans adapts and should be good, this is all done by a electronic tool called a Tech II

Posted on Apr 06, 2012

Testimonial: "Your answer was helpful when I asked GM Buick div. for a solution. They are getting back to me after Easter. Will let you know what they say."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I remove driver door panel?


what car are u talking about most are close to being the same google it

Apr 16, 2016 | 2014 Buick Verano

1 Answer

How to remove door panel on 2014 Buick Verano


Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door. Remove the three screws retaining the front door trim panel to the front door.

Feb 16, 2016 | Buick Verano Cars & Trucks

1 Answer

Where is fuel filter location on a 2014 buick verano


Usually under the vehicle along the frame . follow fuel line from the tank and you will find it .

Dec 29, 2015 | Buick Cars & Trucks

1 Answer

I have 2 Samsung Rugby 3 phones I can get one to connect and give all options includeing phonebook but the other one will connect but not give me my phonebook.


Phonebooks are only there if you put numbers in it , they do not transfer from phone to phone depending on which you pick up .SORRY

Sep 12, 2015 | 2014 Buick Verano

2 Answers

My truck sonoma gmc 2001 dont past the emission test


Definition of Diagnostic Trouble Code P1345 Audi: Ignition Coil Power Output Stage 3 Short to Ground BMW: Misfire Cylinder 2 with Fuel Cut-Off Buick: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Cadillac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Chevrolet: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Ford: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) GMC: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Isuzu: Crankshaft Position - Camshaft Position Correlation Kia: No SGC Signal (1.6L) Lexus: Variable Valve Timing / CMP Sensor Range / Performance Lincoln: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Mazda: Cylinder Discrimination Signal (from CMP sensor) Mercury: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Oldsmobile: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Pontiac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Saturn: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Toyota: Variable Valve Timing / CMP Sensor Range / Performance Volkswagen: Ignition Coil Power Output Stage 3 Short to Ground

Jul 19, 2015 | GMC Cars & Trucks

1 Answer

Engine code139


OBDII PO139

Possible causes
- Timing belt or chain stretched or jumped
- Faulty Camshaft Position (CMP) Sensor
- Camshaft Position (CMP) Sensor harness is open or shorted
- Camshaft Position (CMP) Sensor circuit poor electrical connection.

Read more: http://engine-codes.com/p1391_chrysler.html#ixzz3UeAhEMOH

Mar 17, 2015 | 2000 Buick LeSabre

2 Answers

How too change cabin air filter on2012 buick verano


Remove the glove box from the instrument panel. Behind it is an access door. Remove the cover and the old filter, put in the new filter. Replace cover and glove box.

1_26_2013_7_28_10_pm.jpg


1_26_2013_7_28_32_pm.jpg


1_26_2013_7_28_59_pm.jpg


1_26_2013_7_29_13_pm.jpg


1_26_2013_7_29_30_pm.jpg


1_26_2013_7_29_59_pm.jpg

Dec 29, 2012 | 2012 Buick Verano

1 Answer

2012 buick verano transmission lag


Tell dealer to do a trans flush with a TECH II and reset the trans adapts and should be good, this is all done by a electronic tool called a Tech II

Apr 06, 2012 | 2012 Buick Verano

Not finding what you are looking for?
2014 Buick Verano Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...