Question about Ford F-150

Open Question

Ford F-150 2000 coolant temperature sensor location

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Ford 460 Engine Temp sensor

looking at  the  front of  the engine, just to  the right and behind  the  distributor cap. You  will  see a  wire attached (push on).

Posted on Aug 24, 2008

  • 15 Answers

SOURCE: Coolant temp sensor

it is located where the upper radiator hose enters the thermostat housing

Posted on Jan 27, 2009

  • 155 Answers

SOURCE: How do I change the temperature sensor under the

It’s located on the driver’s side of the engine on top /side of the head.. midway.. I don’t think you need to remove the engine cover to see it.. if it is the correct one it will have a dark green top.. the bad version has a black top… but they can all go out to lunch on you if old enough.

To replace.. make sure the car is cool..
You need a hood tool.. or small pair of pliers to remove the retaining clip that holds it in place.
Place a rag under and around it to catch the coolant.. you will lose less than a half a cup.. if that.

Pull the retaining clip back toward you.. try not to drop it.. (another good reason for the rag)

Wiggle the sensor.. pop it out.. and replace with the new green top one make sure you clean the area well.. and when you reinstall the new one that the c clip goes back on straight or it will leak.

Once you see the part out of the box.. you will understand how it works

Start the car.. check for leaks.. run until warm with the heater on.. top up the coolant overflow bottle with distilled water.. (if more than a half a cup.. you should mix the proper anti freeze and distilled water and then top up with that)

Good luck

Posted on May 06, 2009

  • 119 Answers

SOURCE: replacement of coolant temperature sensor

located under intake in water crossover pipe,you can access the sensor by removing intake chamber box,then pcv hose connected to the block,the connector is orangeish 2pin,use a 19mmdeep socket on a 3/8 ratchet to get it loose,make sure engine is cool,also make sure there is a new brass washer with your new sensor,sometimes the old washer comes off when removing the sensor,sometimes it sticks to the pipe,some coolant will escape so make sure to top it off

Posted on Jul 14, 2009

  • 169 Answers

SOURCE: sensor locations

air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is located the 2006 ford focus of 2.0 engine coolant module temperature sensor


It doesn't have a coolant sensor it has a CHT, cylinder head temperature sensor. This type of sensor is much more precise measuring engine operating temperature.

Oct 13, 2016 | 2006 Ford Focus

2 Answers

Location of temperature sensor that operates the temperature gauge


Follow the upper rad hose to the thermostat housing. It will be there. There are two, one is the ECT (engine coolant temperature SENSOR) and the other is the temperature SENDING UNIT (input for temp. gauge ONLY). f83e91b9-4b48-476a-8c50-10735b376bf1.png

Mar 07, 2014 | 2001 Ford Focus

1 Answer

Loation of a coolant temperature sensor on a 1989 F250 351W


COOLANT TEMPERATURE SENSOR

1989 Ford Truck F250 3/4 ton P/U 2WD 5.8L FI Windsor 8cyl

The Coolant Temperature Sensor is located: Under hood, driver side, upper engine area, rear of water outlet, mounted in intake manifold

Feb 12, 2013 | 2003 Chevrolet TrailBlazer

1 Answer

Location of engine coolant temperature sensor


Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.


12_5_2011_5_38_05_pm.jpg

Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Dec 05, 2011 | 2000 Ford Escort

1 Answer

Where is the temperature sensor located on a ford e-150 with a 302


The ECT (Engine Coolant Temperature) sensor is located either in the heater supply tube at the rear of the engine, or in the lower intake manifold. The ECT sensor is a thermistor (changes resistance as temperature changes).

The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM. From this signal, the PCM will modify the air/fuel ratio (mixture), idle speed, spark advance, EGR and canister purge control. When the engine coolant is cold, the ECT sensor signal causes the PCM to provide enrichment to the air/fuel ratio for good cold drive-away; as engine coolant warms up, the voltage will drop.

10_16_2011_1_04_57_pm.jpg

Fig. Unplug the coolant temperature sensor electrical connection to take off.

Hope this helps and keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment.

Have a nice weekend and thanks for using FixYa.
Jose.

Oct 14, 2011 | 1994 Ford Econoline

2 Answers

Where is the coolant temperature sensor located on a 94 ford f150


The Coolant Temperature Sensor is located under hood, center, front engine area, rear of water outlet, mounted in intake manifold.

Hope helped (remember rated this help) Good luck.

Nov 03, 2009 | 1994 Ford F150 Styleside Supercab

2 Answers

Where is the temperature sensor for a ford e-150 van 1994 on a 300ci v-8 engine. Thanks rick


1994 Ford Truck E150 1/2 ton Van 5.8L MFI 8cyl Temperature Switch is located: Front seating area, center, under engine cover, front driver side of intake manifold, mounted in engine block.

The ECT sensor (Engine Coolant Temperature Sensor) is located either in the heater supply tube at the rear of the engine, or in the lower intake manifold. The ECT sensor is a thermistor (changes resistance as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM. From this signal, the PCM will modify the air/fuel ratio (mixture), idle speed, spark advance, EGR and canister purge control. When the engine coolant is cold, the ECT sensor signal causes the PCM to provide enrichment to the air/fuel ratio for good cold drive-away; as engine coolant warms up, the voltage will drop.

c1fb19f.gif

Engine component locations-1994 5.8L engines

I hope help you with this, good luck (remember rated this help).

Sep 02, 2009 | 2002 Ford E-Series

1 Answer

Sensor locations


air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Aug 29, 2009 | 2003 Ford F150 Regular Cab

1 Answer

Where is the engine coolant sensor located on a 2000 ford f150 V8 4.6 L?


please rate as fixya if this helps

SECTION 303-14: Electronic Engine Controls 2000 F-150 Workshop Manual
REMOVAL AND INSTALLATION Engine Coolant Temperature (ECT) Sensor — 4.6L and 5.4L Removal and Installation
  1. Remove the engine coolant temperature (ECT) sensor.
    1. Disconnect the electrical connector.
    1. Remove the ECT sensor.
ae8a8e7.gif The ECT sensor:
  • sends the PCM a signal indicating engine temperature.
  • resistance decreases as coolant temperature increases.
The ECT measures the temperature of the engine coolant. The sensor is threaded into an engine coolant passage.

Mar 19, 2009 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...