Question about Cars & Trucks

Open Question

I have a hurlcon hx 120 it will ignite but will not stay on 10 seconds

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil light stays on 2006 Caravan. Can I fix this myself?


Turn the ignition switch to On, but do not start the Car. Press the accelerator pedal all the way down three times, very slowly, but within 10 seconds. Turn the ignition off. The light should now stay off

Feb 27, 2016 | 2006 Dodge Grand Caravan

1 Answer

How to re-programme new car batteries in car key ?


1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys have been programmed or no input signal either from the switch or plip keys has been received for 120 seconds.

Nov 08, 2014 | Cars & Trucks

1 Answer

How to code new batteries in car key


1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys have been programmed or no input signal either from the switch or plip keys has been received for 120 seconds.

Nov 08, 2014 | 1999 Nissan Primera

1 Answer

Why would praking lights stay on and dash lights and lights around the heat controls will stay on with the key out


asuming you turn the headlight switch to the off position disconnect the battery wait 10 minuts reconnect also it is normal for them to be on from 30-120 seconds depending on your curticy lighting set up but if thay dont time out try the battery trick

Feb 28, 2014 | 2000 Dodge Caravan

1 Answer

How to reset my anti thift on my 1995 chavey tahoe


I am guessing that it will start only for a second or two then stall out. Well for this you need to turn the ignition on and then try to start the engine. Then leave the ignition on while the security light flashes. It should then stay on solid after about 10 minutes. When light stays on solid then turn off ignition for about 20 seconds then try to start. It should start up. Hope this helps.

Dec 26, 2011 | 1995 Chevrolet Tahoe

1 Answer

Programming ingition key with a chip in it



  • For 1998 and newer Fords there is no way to program a new Transponder key unless you have two already programmed keys. 1998 and older you could do this in about three minutes. This one has to be hooked up to a scanner.

  • Now if you do have two keys already programmed then follow these steps.
  1. Insert first programmed key in the ignition.
  2. Turn the ignition to start (run) for two seconds and back to off. The ignition should stay on for at least one second.
  3. Remove that key and within 10 seconds stick the second programmed key into the ignition. Turn the ignition to start (run) for two seconds and back to off. The ignition should stay on for at least one second.
  4. Remove the key.
  5. Now insert the key needing to be programmed into the ignition (within 20 seconds) and turn the ignition to start (run) for two seconds and then back off.
  6. The security light will light up for 3 seconds indicating the key is now programmed.
  7. Now wait a couple minutes before starting your car and your done.
  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 06, 2011 | 1999 Lincoln Continental

1 Answer

The anti theft system light stays when i drive my 2005 chevy malibu classic


Folllow these steps:
turn ignition to "ON" (dont start the car)
leave it open for 10 minutes.
Turn ignition to "OFF" wait two seconds and turn it back to "ON"
leave it open for 10 minutes.
Turn ignition to "OFF" wait two seconds and turn it back to "ON"
leave it ope for 10 minutes.

Turn it on, start the car normally and have a safe trip. Your system has just relearnt the security passkey.
Good luck.

Jul 08, 2009 | 2005 Chevrolet Malibu

1 Answer

Change oil light stays on for a few seconds


you must reset the oil life . WITHOUT STARTING THE ENGINE, put ignition in the ON position with the dash lights on. NOW this MUST be done within 10 seconds. Push the gas pedal all the way down to the floor and release 3X. This should clear the light. Sometimes necessary to repeat if not done in a timely manner.

Mar 24, 2009 | 2002 Chevrolet TrailBlazer

2 Answers

Resetting 1998 honda civic remote control


ok here is the porcedure that i have for it

Remember , these steps must be preformed within 5 seconds of eachother also all doors should be closed, radio and lights turned off

im not sure what you mean by a bypass, you can always just not use the remotes and go into the body control computer and turn off keyless entry

1) Unlock Doors
2) Turn ignition key to "ON" position (II)
3) Press the "LOCK" or "UNLOCK" button on the remote
4) Turn the ignition key to the "OFF" position (0, I)
5) Turn the ignition key to the "ON" position
6) Press lock or unlock
7) Turn key to off position
8) on position
9) lock or unlock
10) off position
11) on position
12)lock or unlock - doors should cycle to indicate successful programming. If you only have one remote, turn ignition to off or don't touch anything. if you have 2+ remotes, go to 13:
13) lock on each transmitter that you need to program

*Steps 2-12 must be performed within 5 seconds of each other. Step 13 can be performed within 10 seconds of step 12.

Nov 11, 2008 | 1998 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...