Question about Cars & Trucks

Open Question

I have a 1984 vette motor going in 1987 r10 truck flywheels are diffrant

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: 1984 s10 2.8 manual trans. flywheel causes engine to vibrate

no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Posted on Jan 16, 2009

  • 12 Answers

SOURCE: 1984 cadillac eldorado flywheel repair

Yes obviously they will need to lift the motor because the flywheel is smack-dab in between the torque converte and motor, could actually do it yourself with the right tools ( Engine hoist, air compressor , air tools, and sockets, and or course torque wrenches to properly mount the flywheel back to manufacturer specs) but I do believe 3 Grand is way higher then your average shop. Look for shops with Mexicans they have O.K. service for a good price. Reasonable price is in between $700 and $1200 GOOD LUCK!!

Posted on Apr 16, 2009

juncro
  • 467 Answers

SOURCE: Wont go in over drive

check the trany fluid

Posted on Jul 29, 2009

  • 255 Answers

SOURCE: 1987 Chevy R10 project truck won't start

check the float on the carb is stuck shut not letting fuel in

Posted on Aug 17, 2009

  • 2428 Answers

SOURCE: where is the knox sensor

If you face the engine its on the right side about 10:30 to 11:00 O, clock slightly behind the distubtor shaft torward the fire wall you kind of have to crawl over the engine to see it and by the way the oil pressure sending unit is on the oppisite side same pisition

Posted on Dec 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the front turn signal bulb on 1987 chevy r10


Are you sure the socket does not come out from the back ?
The R10 models are just like the C10 models from 1986 and some of them pull out from the back.

Jul 13, 2012 | Cars & Trucks

1 Answer

I have a 1987 Chevy R10 Custom Deluxe with a 305. When I put the truck into reverse or drive it dies.


sounds like a TCC problem (torque converter)
could be stuck valve or defective converter

May 28, 2011 | 1987 Chevrolet R10

1 Answer

Is the c10 the same as the r10?


yes it is but the r10 was only around so long but all the parts are interchangeable

Nov 19, 2010 | 1987 Chevrolet R10

1 Answer

My 1987 Chevy r10 cranks but wont start. i was driving and it just shut off like you switched the key off. i have no spark and injectors don't energize as well.


It is most likely the ignition module,have it tested,if it test good,replace the pick up coil in the distributor,this pulses the injectors.

Jun 26, 2010 | 1987 Chevrolet R10

1 Answer

1987 chevy truck the ignition module keeps burning out what could be causeing this.


need more input, how often do you change it how many miles on motor, are you appying the grease on the bottom of it, are there any cracks on the wires to it

Apr 25, 2010 | 1987 Chevrolet R10

1 Answer

1987 Chevy R10 project truck won't start


check the float on the carb is stuck shut not letting fuel in

Aug 17, 2009 | 1987 Chevrolet R10

1 Answer

Taillight lense removal on 84 vette


If I remember you need to remove them from laying on the ground and going in from under the car behind the bumper. Some models did have 2 screws on the front the older ones had to be removed from behind the bumper.

May 24, 2009 | 1984 Chevrolet Corvette

1 Answer

1984 s10 2.8 manual trans. flywheel causes engine to vibrate


no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Jan 16, 2009 | 1984 Chevrolet S-10

1 Answer

1984 cadillac eldorado flywheel repair


Yes obviously they will need to lift the motor because the flywheel is smack-dab in between the torque converte and motor, could actually do it yourself with the right tools ( Engine hoist, air compressor , air tools, and sockets, and or course torque wrenches to properly mount the flywheel back to manufacturer specs) but I do believe 3 Grand is way higher then your average shop. Look for shops with Mexicans they have O.K. service for a good price. Reasonable price is in between $700 and $1200 GOOD LUCK!!

Jun 24, 2008 | 1984 Cadillac Eldorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...