Question about Mitsubishi Pajero

Open Question

Little red light on steering wheel of pajero that goes on for a few seconds after engine is turned on. what is the purpose of that light?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 90 Answers

SOURCE: check engine warning light

HI
so i think you have fuel injectors problem ??
that may be cause the case of fault !!!
you can test it by diagnoses scan tool
and then ask me for more information
WITH MY BEST WISHES

Posted on Jul 20, 2008

  • 119 Answers

SOURCE: 2004 V6 cold engine noise related to steering - goes away after few miles

check pawer steering pump belt mybe it is worn out or loose, also check the alteranator belt.

Posted on Oct 18, 2008

Technopro
  • 243 Answers

SOURCE: Mitsubishi Colt SRS red light

Hi
This is perfectly normal for this light to com on and going off after a few seconds. The SRS computer needs to make sure all the sensors and airbags are responding at first ignition key on, then if all of them are responding and working, the light goes off.
If it happens that the light doesn't go OFF after 30secs and stays ON all the times then you should pay a visit to your local dealer.
But for now you can enjoy your car safely.
Cheers,
Technopro

Posted on Jan 26, 2009

  • 61 Answers

SOURCE: cannot find my power where my power steering goes

If I remember correctly the power steering fluid fill is on the driver's side at the front of the engine at the same level as the exhaust manifold. It has a black cap and if is dirty is hard to see. Just remember that it is right on the power steering pump and behind the power steering pulley and that should help make it easier to find. Hope this helps. Let me know if it does or you need more help.

Posted on May 03, 2009

  • 11 Answers

SOURCE: servie engine light on traction light goes off

It could be your wheel bearings, jack your car so one wheel is off the ground. Make sure the vehicle is properly blocked. Firmly grasp the tire/wheel an shake it back and forth for play.

Posted on May 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Ford 500 steering wheel locked or power steering not working. Check system alert and battery light turns on.


Call your Ford dealer and ask them if you car has a locking steering wheel.
Since "forever" ago, there was a were "star wheels" attached to the inside of the steering column, for the purpose of preventing theft by locking the steering wheel when the key was removed.. The bad side was that those locks can jamb if the steering wheel
is at the end of it's travel, such as can happen if the front wheel of the car is jammed against a curb when parked.
Your fix might just be to turn the steering wheel whilst trying to start it, though it may take a little muscle.
God bless your efforts.

Jul 04, 2017 | Ford Cars & Trucks

2 Answers

How to bleed power steering on F350 Diseal


If you make sure your fluid lvl is topped off and start the truck up, turn the steering wheel all the way to the right and hold it there for a few seconds then go all of the way to the right and hold it there for a few seconds. Repeat this a few times and it should work all of the air out of the system. You will probably need to check the fluid level a few times as when it burps the air out the fluid lvl will naturally drop.

Apr 21, 2013 | Cars & Trucks

1 Answer

Steering is noisy at slow speeds when turning


This car is essentailly the same as the Lincoln LS & T-Bird.
Here is their solution.

please rate if this helps you. Thanks.

ISSUE: Some 2003-2005 Thunderbird, Aviator, and Lincoln LS vehicles may exhibit steering gear squeak when turning the steering wheel, especially during low speed parking maneuvers. The noise may sound like it is coming from the steering column area and may be felt as a roughness in the steering wheel, while turning.
ACTION: Refer to the following Service Procedure.
SERVICE PROCEDURE NOTE: USE ONLY THE FLUID AND ADDITIVE SPECIFIED IN THIS ARTICLE. USING ANY OTHER FLUIDS OR ADDITIVES MAY RESULT IN SEAL DETERIORATION AND LEAKS.
  1. Open the hood and remove the power steering reservoir cap.
  2. Raise the vehicle on a hoist. Refer to Workshop Manual, Section 100-00.
  3. With engine off, drain power steering fluid by disconnecting steering lines and clamp plate from steering gear. Refer to Steering Gear Removal and Installation procedure in Workshop Manual, Section 211-00, follow only the steps required to disconnect the steering lines.
  4. Turn steering wheel lock-to-lock to drain fluid completely.
  5. Reconnect steering lines and clamp plate to steering gear. Torque retainer to 15 N-m (11 lb-ft) for Lincoln LS and Thunderbird, torque to 25 N-m (18 lb-ft) for Aviator.
  6. Lower vehicle.
  7. In a clean container mix 50 ml (10 teaspoons or 1.7 oz.) of Motorcraft Additive Friction Modifier, Part Number XL-3, with 50 ml of Motorcraft MERCON® Multi-Purpose Automatic Transmission Fluid, Part Number XT-2-QDX. NOTE: DO NOT PERFORM STEPS 8 AND 9 ON A HOT VEHICLE.
  8. Pour the above mixture into the power steering reservoir.
  9. Top off (fill) the power steering system with Motorcraft MERCON® Multi-Purpose Automatic Transmission Fluid, Part Number XT-2-QDX and reinstall the power steering reservoir cap.
  10. Raise vehicle on hoist enough so the front wheels are off the ground and can be turned from lock-to-lock.
  11. Start the engine and keep it at idle. Remain inside of the vehicle.
  12. Slowly cycle the steering wheel from lock-to-lock for two (2) minutes.
  13. Quickly and forcefully turn the steering wheel in one direction to full lock (either side). Bounce the steering wheel on/off of full lock twenty (20) times forcefully. NOTE: IT IS CRITICAL THAT THE STEERING WHEEL IS TURNED QUICKLY AND FORCEFULLY IN ORDER TO CREATE A PRESSURE SPIKE IN THE POWER STEERING SYSTEM.
  14. Repeat Step 13 in the other direction. Return the steering wheel to on center position.
  15. Slowly turn steering wheel to full lock in one direction (either direction) to achieve maximum pump pressure. Hold at full lock for one (1) second, then turn the steering wheel back 90 degrees as quickly as possible. Repeat this procedure twenty (20) times. NOTE: DO NOT HOLD THE STEERING WHEEL AGAINST THE STOPS FOR MORE THAN THREE TO FIVE (3-5) SECONDS AT A TIME. DAMAGE TO THE POWER STEERING PUMP MAY OCCUR.
  16. Repeat Step 15 in the other direction.
  17. Cycle the steering wheel slowly for 1 minute to confirm that the squeak is corrected and return vehicle to the customer. NOTE: IF THE SQUEAK CONTINUES, REPEAT STEPS 13-16 ONE ADDITIONAL TIME. IF THE SQUEAK IS STILL NOT CORRECTED PROCEED TO STEP 18.
  18. If the squeak is still present after performing Step 17, replace the steering gear. Refer to Workshop Manual, Section 211-00 for removal and installation procedures.

PART NUMBER PART NAME XL-3 Motorcraft Additive Friction Modifier XT-2-QDX Motorcraft MERCON® Multi-Purpose Automatic Transmission Fluid 5W4Z-3504-A Steering Gear (LS) 5W6Z-3504-A Steering Gear (Thunderbird) 5C5Z-3504-AA Steering Gear (Aviator)

Aug 15, 2011 | 2003 Jaguar X-Type

1 Answer

To start with my power steering pump was making a little noise and also had bubbles in the resevoir so i put a new power steering pump on it.not a rebuilt one. when i started it up i still have the bubbles...


Section 11-00: Steering System-Service 1999 Taurus, Sable Workshop Manual SERVICE PROCEDURES Purging Power Steering System of Air NOTE: If the air is not purged from the power steering system correctly, a second customer concern or pump failure could result. This condition can only occur on pre-delivery vehicles with evidence of aerated fluid or vehicles that have had steering component repair.

A whine noise heard from the power steering pump may be caused by air in the system. The following procedure must be performed whenever any of the following are performed:
  • All power steering noise complaints with evidence of aerated fluid on pre-delivery vehicles only, prior to any component repair.
  • After any power steering system component (for example, gear or hose) has been replaced and the noise is heard.
Fluid Level Top-Off Procedure
  1. Check and fill pump reservoir to dipstick full cold or remote reservoir center mark.
  1. Disable ignition by removing Fuse 10 in the fuse junction panel.
  1. Crank engine 30 seconds, check fluid level and add if required.
  1. NOTE: Do not hold steering wheel on stops.

    Crank engine 30 seconds while cycling the steering wheel lock to lock.
  1. Check fluid level and add fluid if required.
Air Purge with Vacuum External Source Procedure - 3.0L (2V) Engine, Flex Fuel and 3.4L SHO Engine
  1. Tightly insert the rubber stopper of the air evacuator assembly into pump reservoir.
  1. Reinstall Fuse 10 used to disable ignition and start vehicle.
  1. Apply 20-25 in-Hg (85-88 kPa) maximum vacuum for minimum of three minutes at idle; maintain maximum vacuum with vacuum source.
  1. Release vacuum and remove vacuum source.
  1. Add fluid to full warm or reservoir center mark.
  1. Reinstall vacuum source and apply 20-25 in-Hg (85-88 kPa) vacuum.
  1. NOTE: Do not hold steering wheel on stops.

    Cycle steering wheel from lock to lock every 30 seconds for approximately 5 minutes.
  1. Shut engine off, release vacuum and remove vacuum source.
  1. Add Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid if necessary and install dipstick or reservoir cap.
  1. NOTE: Do not hold steering wheel on stops.

    Start engine and cycle steering wheel from lock to lock every 30 seconds for approximately 5 minutes.
  1. Check for oil leaks at all connections.
  1. In severe cases it may be necessary to repeat air purge with vacuum source procedure.
Air Purge with Vacuum External Source Procedure - 3.0L (2V) and 3.0L (4V)
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to approximately 2.5 cm (1 in) (make a mark) above the top of the supply line.
  1. Tightly insert the rubber stopper of the air evacuator assembly into the pump reservoir.
  1. Apply 85-88 kPa (20-25 in-Hg) maximum vacuum for a minimum of three minutes.
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent until the level is at the marked point.
  1. Repeat Steps 3 and 4 until the fluid level stabilizes.
  1. Check reservoir level and add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to the FULL WARM (MAX) mark.
  1. Install the number 10 fuse in the fuse junction panel. Start the engine.
  1. NOTE: The front wheels must be off the floor during lock-to-lock rotation of the steering wheel.

    NOTE: Do not hold the steering wheel on stops.

    Reinstall the vacuum source and apply 85-88 kPa (20-25 in-Hg) maximum vacuum and cycle the steering wheel from lock-to-lock every thirty seconds for a minimum of 5 minutes.
  1. Shut the engine off, release the vacuum and remove the vacuum source.
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to the FULL WARM (MAX) level. Install the dipstick or reservoir cap.
  1. NOTE: Do not hold the steering wheel on stops.

    NOTE: In severe cases, it may be necessary to repeat air purge with vacuum source procedure.

    Start the engine and cycle the steering wheel from lock-to-lock every thirty seconds for approximately five minutes.
  1. Lower the vehicle front end.
  1. Check for oil leaks at all connections.

Jul 24, 2011 | 1999 Ford Taurus

1 Answer

WeMy power steering fluid was leaking I tool it to the shop they told me It was the pump so I brought a new pump and got It put in and now I still cant turn my steering wheel


HEY DO THIS,YOU NEED TO BLEED SYSTEM. TO BLEED POWER STEERING SYSTEM.TO DO THIS.FILL THE POWER STEERING RESERVOIR TO COLD FULL MARK ON DIP STICK.WAIT A FEW MINITES,FLUID LEVEL DROP ADD MORE FLUID UNTIL REACH COLD MARK ON THE DIP STICK..WAIT FEW MINUTES.START ENGINE LET IT RUN FOR 2 OR 3 SECONDS.TURN OFF ENGINE CHECK POWER STEERING FLUID ADD MORE FLUID.DO THIS UNTIL FLUID LEVEL STOP DROPPING.WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE FRONT OF THE VECHICLE UNTIL FRONT WHEELS DONT TOUCH THE GROUND.START ENGINE UP.TURN THE STEERING WHEEL GENTLY FROM STOP TO STOP,CHECK THE RESERVOIR FLUID LEVEL LOOKS GOOD TURN OFF ENGINE LOWER VECHICLE .LOWER VECHICLE TO GROUND. LET VECHICLE SET FOR 2 MINUTES CHECK POWER STEERING FLUID LEVEL.IF STILL LOW ADD LITTLE MORE.TO THE COLD FULL MARK ON DIP STICK. DONT OVER FILL BECAUSE FLUID LEVEL RISES WHEN IT GET HOT.WHEN DONE IF STEERING WHEEL STILL FEEL HARD TO TURN YOU SEE AIR BUBBLES IN FLUID THATS WHEN FLUID HAS A TAN LOOKING COLOR WAIT 5 MINUTES AND.REPEAT THE BLEEDING PROCESS. DONT DRIVE OR OPERATE VECHICLE ON HIGHWAY UNTIL POWER STEERING HAS NORMAL OPERATION.

Sep 26, 2010 | 1999 Oldsmobile Alero

1 Answer

When i put my mitsubishi pajero into 4X4 and make a full turn


were you on hard ground when you tried turning on 99 % of your 4x4 your wheels have to be in very loose dirt ,sand. snow. mud when turning sharp if you were on a hard surface the sound was your front axle trying leave your 4x4 but if you were not look at your transmission mount and motor mounts i actually sheered off my tranny mount trying to crawl sharply over large rock i was in dakota my truck engine attached to front axle axle turns motor shifted trans mount broke

Jan 26, 2010 | 1992 Mitsubishi Montero

2 Answers

Car wont start


IS THE RED LIGHT THAT IS STAYING ON THE BATTERY LIGHT? IF SO IT COULD BE AN ELECTRICAL FAULT, AND IS NOT FIRING UP THE ELECTRIC FUEL PUMP

Mar 13, 2009 | Acura CL Cars & Trucks

1 Answer

2004 V6 cold engine noise related to steering - goes away after few miles


check pawer steering pump belt mybe it is worn out or loose, also check the alteranator belt.

Oct 18, 2008 | 2004 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...