Question about Jeep Cars & Trucks

Open Question

2006 5.7 jeep commander map sensor location - Jeep Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

  • 6982 Answers

SOURCE: where is map sensor located on 1999 jeep grand

MAP is usually on the firewall...it's about 1/2" thick by about three inches long, has a vacuum hose and several wires plugged into it.

Posted on Aug 15, 2009

dburns60
  • 410 Answers

SOURCE: where is the map sensor located? 1994 jeep grand cherokee

Go half way between the air cleaner box and the "carburetor". Up the 4" black air pipe, a wire harness plug plugs into the MAP sensor there. Also called MAS air flow sensor.

Posted on Oct 05, 2009

  • 645 Answers

SOURCE: ac/heater fan switch problem on a 2006 jeep commander

next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Posted on Feb 13, 2010

Testimonial: "This info was very helpful but need a little more info of where the fan motor is located. I will post another question to find that info."

Gozer
  • 435 Answers

SOURCE: install a altenator for a 2006 jeep commander

I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

Posted on May 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the map sensor on 2006 Jeep commander


if it has one, at all, (and not mAF)
you unbolt it.
if it has hose that too comes off (if not a direct intake mounted type.
it will have a 3 pin connector and will need to come off first
all conn. on cars have locks do not force them,
no engine option stated, so no real list of exact steps. possible

the engine line up is.

  1. 3.0 L OM642 V6 (turbocharged diesel)
  2. 3.7 L PowerTech V6 (gasoline)
  3. 4.7 L PowerTech V8 (gasoline / E85)
  4. 5.7 L Hemi V8 (gasoline) (may have a MAF?)

so what engine?, its an engine question and fist just is to know what is there....

Jul 29, 2015 | Jeep Cars & Trucks

1 Answer

Where is the hvac blower fuse located on 2006 jeep commander


triple anon posted now.
open the glove box, take out the operate guide, read the fuse page.
lost it, then get one.

answered twice now,
http://www.jeep.com/en/owners/manuals/

there it is again
here, 3 times.
http://www.jeep.com/en/owners/manuals/

Sep 24, 2014 | 2006 Jeep Commander

1 Answer

Whaer is the rear senor location


There is no rear sensor they got 02 sensors map sensors air intake sensors..what rear on top or under the car you mean by rear

Jul 03, 2014 | 2006 Jeep Commander

1 Answer

Engine cooling fan does not run on 2006 jeep commander


Check ur fan sensor u can find the diagram of the sensor location on google and their cheap and easy like a spark plug to install.

Feb 16, 2013 | Jeep Commander Cars & Trucks

1 Answer

Where is the speedometer cable located on a 07' jeep commander 4.7l v8 on the transmission? Please be specific as possible. Thank You


Your Jeep doe not have a speedometer cable. The speed is calculated by the PCM ( vehicle computer) by input values that are received from the vehicle speed sensor. This issue is most likely not repairable by the average person without the proper scan tool required to do so.

Jun 01, 2011 | 2006 Jeep Commander

1 Answer

2006 Jeep Commander inefficient catalyst


most likely the oxygen sensors (lambada) ,they need changing ,their are two one before the cat and one after,do not think you need a new cat unless it has a min of 150.000 miles on the clock

Jul 02, 2010 | 2006 Jeep Commander

2 Answers

I need to replace the map sensor in my 06 jeep liberty diesel...i was wondering if you know the location of the map sensor...i think it is location inside the airbox


The Manifold Absolute Pressure sensor is located on top of the cylinder head, right side, about 2/3 of the way back. there is one screw holding it in. You will need to take off the plastic engine cover off to access it. The sensor in the airbox is the MAF sensor.

Jan 24, 2009 | 2006 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...