Question about Cadillac Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: How do I read the
if it's the check engine light. since your car is 1996 and newer take it to the local autzone, advance auto (free) have them plug into it and read the codes (OBDII). take a pen and paper so that you can write down what comes up. Or take it to your local mechanic and have him/her read the codes ($Free-$60). anything outside of the check engine light, you will need to go to a garage / dealer.
Posted on Sep 22, 2008
SOURCE: replacing spark plugs
Changing spark plugs in your Cad is not an easy thing. I tried it using the chiltons manual and it took five hours. Just in case you want to try it yourself you will need to start by removing the engine cover (two screws easy to locate). Next step is the tricky and tedious part. A black cylider with small vacuum tubes located at the rear center next to firewall needs to be removed. It is attached to the engine by an somewhat difficult to reach bolt and a almost impossible lower bolt that can be acessed underneath if you can find it and have hand of a ten year old. I removed it from bottom of vehicle than tightened it after from the top this is by far the most difficult of the process watch your knuckles. This vacuum valve is connected to a silver hose which needs to be unscrewed to remove valve two screws attach it from the bottom. This is another difficult one. Make sure the your socket is firmly onto the wrench, one socket remains hidden after it fell off, making a extra trip to the store neccasary after losing it. Move valve out of the way as best you can and what remaing are 8 bolts holding on the "ignition coil assembly". These shoul be taken out in a "W" pattern: top bottom top bottom. Remove these and remove panel another very tight fit. Remove spark plug boots and take out spark plugs and keep in order so that spark plug damage can be assessed according to corrisponding cyclider. Repeat for front plugs and reverse steps to reassemble. Spark plugs come pregaped. Start with the rear plugs, they are the most difficult, and you have a better idea how much time it will take.
Posted on Sep 29, 2008
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls
Posted on Sep 23, 2009
P0741 Torque Converter Clutch Circuit Performance or Stuck Off
Your car actually has a viscous converter clutch inside the torque converter instead of a (mechanical) torque converter clutch to lock up the torque converter for fuel economy improvement. You will see it referred to as the VCC and/or TCC.....
The TCC/VCC has a variety of components in the system including an electrical circuit supplying the transmission, the apply solenoid inside the trans, the torque converter itself, the PCM that controls the apply, etc. It is impossible to diagnose from afar. Unlikely that it is a "sensor" inside the trans as the PCM controls the VCC apply and uses engine and trans data that it receives from a variety of sources. If a "sensor" had failed the trouble code for that sensor would be setting......
Something as simple as the brake switch can cause the VCC to not apply correctly. There is a safety switch on the brake pedal that activates the brake lights and disconnects the VCC circuit. If it is misadjusted then the trans cannot apply the VCC. Lots of other trouble shooting items on the VCC system. If you don't have a service manual and cannot trouble shoot the system, I would recommend a Cadillac dealer as they have the trouble shooting information for the specific VCC that the Cadillac 4T80E trans has that a trans shop is simply not familiar with. No sense working on the trans until you actually know what is wrong.
Posted on Jan 13, 2010
crankshaft sensor is and the hormonic balance pulley and cam sesoor should b and the front of the motor toward the top. But to b sure u should get a book for u vehical
Posted on Mar 09, 2010
Tips for a great answer:
Aug 21, 2017 | Cadillac Cars & Trucks
Nov 14, 2016 | Cadillac Cars & Trucks
Feb 17, 2016 | Cadillac Cars & Trucks
Nov 19, 2015 | Cars & Trucks
Dec 30, 2013 | 2002 Cadillac Deville
Sep 04, 2013 | 2002 Cadillac Deville
Apr 20, 2017 | 2002 Cadillac Deville
Nov 28, 2010 | 2002 Cadillac Deville
Jul 26, 2008 | 2004 Cadillac Deville
14 people viewed this question
Usually answered in minutes!