Question about Nissan Cars & Trucks

Open Question

I need the torque specification intake manifold 2013 nissan quest

Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 21873 Answers

SOURCE: When I tune up my 04 Nissan Quest do I need a Intake Manifold Gasket?

If you have to remove the top half or plenum of the intake manifold, it is always recommended to replace the gaskets. I have squeaked by without doing it if the gaskets are in good condition.

Posted on Aug 25, 2012

  • 11 Answers

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

#1 is top right most bolt first, 2nd is farthest to the left on top, #3 is the one down and to the left of # 2, #4 is on top and to the left of #1, #5 is the hardest one to get to and is right in the middle on the bottom, and #6 is only one left which is top middle....
on re-installation you go backwards and torque from 2--22 NM

Posted on Mar 09, 2013

  • 79865 Answers

SOURCE: I need the specific torque for the Intake Manifold bolts of the car Nissan Tiida ST series C11 Year 2011.

Iintake manifold 12-14 ft/lbs

Posted on Jul 12, 2016

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

(1) What is the specific Newtom torque or lb-ft for the sparks plugs NGK LZKAR6AP-11 for Nissan Tiida St C-11 2011. Engine: MR18075675R, Vin:MNBBAC11A0016494.

You miss understand why things need to be torqued .
Torque is not specific to the vehicle its the bolt how hard what is thread pitch how many threads per in or mm how many bolts and what kind compression is required .
Compression always needs to be even say you have a cork gasket on an oil pan with 25 bolts 10 ft lbs on each would give you 250 ft lbs of force but if not done in stages evenly you would be snapping bolts and bending the pan and would leak oil from the start .
Spark plugs have seals 5/8 25 lb ft is fine but its not something you are going to get a torque wrench on .

Jun 15, 2016 | Nissan Tiida Cars & Trucks

1 Answer

98 ford windstar intake manifold torque specs

Intake torque specs ' > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Bolt torque sequence on 1991 jaguar xj6 4.0 intake manifold?

intake manifold or head gasket? i know head gasket need a sequential order followed by how many degrees and Lbs of pressure. if its on the intake i doubt it needs an specific torque. just try not to crack the intake manifold since its made of plastic.

Oct 29, 2012 | 1991 Jaguar XJ6

1 Answer

When I tune up my 04 Nissan Quest do I need a Intake Manifold Gasket?

If you have to remove the top half or plenum of the intake manifold, it is always recommended to replace the gaskets. I have squeaked by without doing it if the gaskets are in good condition.

Aug 24, 2012 | Nissan Cars & Trucks

1 Answer

2004 nissan quest no spark

Pcv hose on upper rear of intake manifold rotted through and causing a vacume leak. spray carb cleaner at mid rear of manifold and idle will drop and stall. pretty hard to replace but thats nasty nissan.

Aug 21, 2010 | 2004 Nissan Quest

1 Answer

2000 nissan quest engine tightening specifications 3.3 engine. I need exhaust manifold

tighten with a 3/*8 drive rachet and that will be enough ,small grunt when pulling on the rachet and you will have the correct torque .about 35 lbs

Jul 22, 2010 | 2000 Nissan Quest

1 Answer

Understanding trouble codes for my vehicles

first the quest, this is common for nissan, replace the knock sensor, this sensor is located under the intake manifold rear of engine, some models you can sneak sensor out without removing the intake, this will take care of that car. now the camry, im guessing this is a 4 cylinder engine, replace the air fuel sensor (oxygen sensor) thats on the exhaust manifold. this will solve that problem. hope this helped.

Jan 25, 2010 | 1999 Toyota Camry

1 Answer

Cylinder head torque specifications 2000 nissan quest

this is a rather involved procedure, it must be done in a very exact manner also you must have a torque angle gauge. if you have this send me your e-mail and i'll try to send you a copy right from ALLDATA. sorry no other way. hope this helps Thanks Ray PS you also have to do the intake at the same time

Dec 11, 2009 | 2000 Nissan Quest

1 Answer

No intake manifold diagrams

this is a repair for an experienced tech, especially the timing belt.

Go here for photos and files.

Feb 02, 2009 | 1996 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides