Question about BMW Cars & Trucks

Open Question

2006 bmw 325i no start have ode 2E7C getting half crank when disconnected intake cam sensor it's getting full crank an trying to start

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chrischronic
  • 235 Answers

SOURCE: 1998 528i bmw cam shaft sensor location

hope this helps .
http://picasaweb.google.com/mmm635/CamshaftPositionSensorsCamshaftPulseGeneratorsAsBMWCallsIt#

not the same year but should be same place.

Posted on Dec 20, 2008

russet327
  • 2 Answers

SOURCE: 1996 Jeep Grand Cherokee No Start

I would be thinking that there is a good chance that you need to be checking out replacing the computer, if you aren't getting any communication with the proper scan tool then the computer isn't communicating with anything in the vehicle...... I would have guessed first off that the ignition control module might be bad but that is obviously part of the computer also, I would be looking in that direction.

Posted on Sep 19, 2009

youredone82
  • 426 Answers

SOURCE: how do I RESET BRAKE LIGHT ON 2006 BMW 325I.Brake

that has to be done by a dealership with a BMW specifiic scan tool

Posted on Oct 30, 2009

luisdelgado5
  • 1 Answer

SOURCE: 1995 BMW 325I WONT START NO CLICK NOTHING ONLY

in not the batery and starter the securyty sistem activad is not signal to the stater from ews ii to starter

Posted on Jan 06, 2010

  • 972 Answers

SOURCE: 2002 Kia Sportage will not start.

p0560 is system voltage problem. open or short between the battery positive and the ecm.CHECK ALL FUSES. dosnt matter what they are labeled under dash and under hood replace any that are bad and retry to start. no start then check voltage to ecm grounds to. i dont have a wireing diagram to give you but for a small fee or free the dealer can make you a copy.make sure all the wires that go to battery terminals are not corroded and are making good contact [verified with volt meter]. if after all checks ok then replace ecm. as a side note i havent had to change one ever.

Posted on Apr 11, 2010

Testimonial: "Thank you for the help. We will continue to check all fuses and wires."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 bmw 325i it crank but wont start it show a code p1727 and u114b. What that mean.


p1727 is crank sensor fault.
u114b torque controller failed,
now the sensors fault for the crank might be false this can be that the u114b is not relaying the signal, it could be the cable to the auto box, you would need to locate the wire and socket under the car and see if its connecting properly, muck and road wash can damage the seal on the connector and let water in.

May 19, 2017 | 2006 BMW 325i

1 Answer

2e7c fault how to fix it


It's a factory OBD2 code specific to your make and model. Either find the list of codes(frequently difficult) or see the dealer. It usually has to do with something other than the engine or drive tran. Found something on a BMW site. they replaced the water pump & thermostat to fix the problem. Read all the posts on the link I provided.
2E7C and water pump on constantly when car off N54Tech com Your Source for...

May 16, 2016 | 2006 BMW 325i

2 Answers

I have a bmw e30 325i it cranks but will not start so what can I do to fix it?


Fuel Pump - can you here the pump (usually under the right hand back seat) running with ignition on?
Fuel Delivery (injectors) - squirt some fuel (just a cap full) into the manifold.
Spark - pull a lead off a spark plug and use a spare spark plug resting on the exhaust manifold.
Crank sensor - Injectors won't inject fuel if the ECU thinks the engine isn't turning. Crank sensor is at the front right lower side and as it gets older, the wire gets brittle and breaks most of the time where it meets the hard end. The connector is under the throttle body and should read 500-600 ohms.

bmw-e30-325i-cranks-but-will-not-start-0egsa4g0vt3f5pkv1piq2dve-5-0.jpg

Dec 26, 2014 | BMW 325i Cars & Trucks

1 Answer

How do i install a starter on a bmw 325i 2006?


remove the intake manifold to get access.

Oct 23, 2014 | 2006 BMW 325i

1 Answer

Why engine has no ignition spark and no injector pulse?


Did you use a code reader? The camshaft sensor when bad will also not allow the car to start.

Aug 08, 2014 | 2006 BMW 325i

1 Answer

Error code p1040


P0140 BMW P0140 BMW - O2 Sensor Circuit Low Voltage Bank 1 Sensor 2



Possible causes - Faulty Rear Heated Oxygen Sensor Bank 1
- Rear Heated Oxygen Sensor Bank 1 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Replacing the Rear Heated Oxygen Sensor Bank 1 usually takes care of the problem
http://engine-codes.com/p0140_bmw.html

Apr 22, 2014 | 2006 BMW 325i

1 Answer

94 bmw 325i will not start, no spark i have a 1994 bmw 325 is it has fuel but no spark replaced computer and wiring harness


What about your coil packs are they working? it can always be a cam sensor or crank sensor

May 30, 2009 | 1994 BMW 3 Series

1 Answer

I have a 1993 bmw 325i and a need to change a crank position sensor and i just want to know How do you replace the crank sensor on a BMW?


Hi the crank shaft sensor is located just above the front pulley at the front of the engine and is held in place be a 5mm hex bolt, undo this and remove the sensor then you will need to follow the wire that dissapears under the intake manifold and unplug the multiplug, replacement is the reverse, regards mark

May 04, 2009 | BMW 325 Cars & Trucks

1 Answer

Dies and wont restart. 1991 bmw 750il


You have a cam or crank sensor that has gone out.

May 01, 2009 | 1991 BMW 7 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...