Question about Toyota Cars & Trucks

Open Question

I NEED THE TORQUE DIAGRAM AND ITS LBS FOR A TOYOTA CARMRY 2.4 LITS 2002

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: I have a weird torque

the dial is for 161 162 ------168 etc count it up to 228

Posted on Apr 23, 2009

Ad
  • 1201 Answers

SOURCE: need head bolt,intake upper and lower and rocker arm torque lbs.

Head bolts--------- 22 ft lbs.
Intake upper------ 18 ft lbs.
Intake lower------- 10 ft lbs. Tighten vertical bolts first, the diagonal bolts, failure to do this will result in an oil leak.
As far as the rocker arm bolts, they have to be adjusted with the valves closed, tighten down just enough to turn the push rods with your fingers with slight tension.
This is out of a Technical Specifications Manual.

Posted on Jul 30, 2009

  • 617 Answers

SOURCE: what are the head bolt torque specs in lbs for a

Cylinder Head Torgue is 58 ft. lb

Posted on Feb 17, 2010

  • 496 Answers

SOURCE: 2002 isuzu rodeo cylinder head torque lbs. for 2.2

Print


Removal & Installation

2.2L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following: Negative battery cableIntake Air Temperature (IAT) sensor connectorPositive Crankcase Ventilation (PCV) valve and hoseAir intake assemblyUpper radiator hoseAccessory drive beltExhaust front pipeAlternator and bracketsCrankshaft Position (CKP) sensor connectorKnock sensor connectorHeater hosesWater bypass hoseFuel linesEvaporative Emissions (EVAP) valve connectorCanister hoseIntake manifoldEngine wiring harness connectors at left rear of the engine compartmentPower steering pump pressure switch connectorFront coverSpark plugs and wiresCamshaft Position (CMP) sensorValve coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulleysTiming belt rear coverOil pressure switch connectorCamshaftsCylinder head. Remove the bolts in reverse of the tightening sequence.

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:


0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine

NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows: Step 1: 18 ft. lbs. (25 Nm)Step 2: Plus 90 degreesStep 3: Plus 90 degreesStep 4: Plus 90 degrees
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following: CamshaftsOil pressure switch connectorTiming belt rear coverTiming belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm).Timing beltValve coverCMP sensorSpark plugs and wiresFront coverPower steering pump pressure switch connectorEngine wiring harness connectors at left rear of the engine compartmentIntake manifoldCanister hoseEVAP valve connectorFuel linesWater bypass hoseHeater hosesKnock sensor connectorCKP sensor connectorAlternator and bracketsExhaust front pipeAccessory drive beltUpper radiator hoseAir intake assemblyPCV valve and hoseIAT sensor connectorNegative battery cable

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt procedure. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:

0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine


NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows:
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following:

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

Posted on May 26, 2012

GeoffW1
  • 3961 Answers

SOURCE: i need how much torque the head bolts for toyota camry 1996

It is 36 ft-lb, but done in two stages to a prescribed sequence.The bolts should be oiled. See here p67

http://www.turboninjas.com/camry/eg1.pdf


This is for the 4-cyl. The V6 is 40 ft-lb, and the link is .....eg2.pdf.

Posted on Aug 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

What is the final torque in ft lbs for the head bolts for 2.4 2003 toyota camry


clean bolt threads and clean out the threads in the head. Lightly oil the bolt threads and tighten in the correct sequence to 36 ft/lbs Using a degree spanner tighten in sequence 90 degrees and the again in sequence another 90 degrees . The final torque is in degrees not ft/lbs. Go on line to toyota camry head bolt torque then find the autozone page and you will find diagrams of how to do it.

Oct 05, 2014 | Cars & Trucks

1 Answer

What are the torque specs on a 2002 toyota sienna's spark plugs, air intake manifold, and valve covers? Thank you.


Spark plug torque on the 3.0L engine is 13 ft.lbs. and the 3.3L is 18 ft.lbs.

Valve covers-69 inch lbs.

Intake Manifold-11 ft. lbs.

Jul 07, 2014 | 2002 Toyota Sienna

1 Answer

Torque the cylinder head bolts for mitsubishi lancer 2002


Try this
I dont know which engine you have.

420a
1. Torque all center bolts to 25 ft-lbs, torque the 4 corner bolts to 25 ft-lbs
2. Torque all center bolts to 50 ft-lbs, torque the 4 corner bolts to 50 ft-lbs
3. Re-Torque all center bolts to 50 ft-lbs, re-torque the 4 corner bolts to 50 ft-lbs
4. Tighten all bolts in the sequence from #1-#10 an additional 1/4 turn.

7-Bolt 4G63
1. Torque all bolt to 58 ft-lbs in order
2. Loosen all bolts completely to 0 ft-lbs
3. Torque all bolts to 15 ft-lbs in order
4. Tighten all bolt 1/4 turn in order
5. Tighten all bolts an additional 1/4 turn in order.

ARP Head Studs
1. Tighten all bolts to 40 ft-lbs
2. Tighten in steps of 10 ft-lbs increments until the specified torque that you are looking for is reached. This can vary with the amount of boost you plan on running.

Jun 30, 2011 | 2002 Mitsubishi Lancer

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

1 Answer

Hi what is the head torque on a 2002 honda civic


Dont forget to apply clean engine oil to the threads of each bolt for proper torquing. Then finger tighten. Then

    1. Tighten the cylinder head bolts to their final torque specification in 4 steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows: Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).


  • Mar 25, 2010 | 2002 Honda Civic

    1 Answer

    Need torque specs for a 2002 toyota camry 2.4 for the head bolts


    The 2002 2.4 engine head bolts are 'torqued to distance'.

    First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

    Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.

    We hope that this helps you out.

    Dec 29, 2009 | 2002 Toyota Camry

    2 Answers

    Replacing the head on a 1992 toyota 1.6 what are the torque specs i will need


    There are apparently 2 different 1.6 motors.
    The 4AFE: front 8-6-1-3-9
    of vehicle 10-4-2-5-7
    tighten in 3 steps, 1. 20 ft lbs 2. 30 3. 44

    The 4AGE front 8-4-2-5-9
    of engine 10-6-1-3-7
    tighten in 5 steps: 1, 10 2. 15 3. 22 4.an additional 90degrees and 5. an additional 90 degrees again.

    Jul 19, 2009 | 1991 Toyota Corolla

    1 Answer

    Torque specs for 1998 tercel 1.5L


    Main Bearing Cap Torque-42 Ft. Lbs.
    Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
    Rod Bearing Nuts-29 Ft. Lbs.

    Hope this helps

    Apr 08, 2009 | 1998 Toyota Tercel

    1 Answer

    Need torque settings for 1985 4A corolla cylinder head


    hey, torque must be done in 3 steps:
    1st 22 ft lbs
    2nd 43 ft lbs
    final 47 ft lbs
    use this sequence of tightening:

    9 - 3 -1 -6 -8
    7 - 5 - 2 -4 - 10

    Jan 14, 2009 | 1985 Toyota Corolla 2 Door

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    24 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    76691 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8531 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...