Question about Rover Cars & Trucks

Open Question

I have a Rover 75 and would like to know if the roof can be split along the plastic seam covers. If so, I want to look at replacing it with one that has a factory sunroof in it. Thank you. Terry.

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017



Have you tried the dealer or wholesale sites like ?

Posted on May 09, 2009

  • 1986 Answers

SOURCE: replacing rear bulbs on rover 75 tourer

With the trunk open, look along the side of the lens assembly and you should see some screws, remove those and you can pull the assembly out. Then twist the sockets on the back of the assembly to free the bulbs

Posted on Sep 16, 2009

  • 11 Answers

SOURCE: 95 GRND CHEROKE sunroof supports have come loose and it leaks.

The bigest problem with this model jeep sunroof is the cable conduit in the rear of sunroof is broken loose. can be accesed by removing the headliner. But the tracks are accessed from the sunroof opening after removing the glass. the part department at the dealership can give you a breakdown basicly the only replacable parts are the tracks, Price about $200.00 each.

Posted on Jan 07, 2010

  • 369 Answers

SOURCE: 1996 Range Rover SE Rear Brake

Replace the wheel cylinder on the wheel where you see it leaking then bleed brake system you ought to be ok on your brakes. As for the sun roof sounds like part of the track system is stripped happens all the time on automatic shoulder belts you can hear the motor running but no movement.

Posted on Jan 05, 2011

  • 25 Answers

SOURCE: My 2002 Land Rover SE

same thing happened to me in a parking garage.. i needed to go to the hardware store and get one of those drill bits that extracts bolts.. i think it was 1/4" size but you should check to see with a 1/4" drill bit..
if it broke off so you have some access to plastic housing.. then its easy with pliers but if yours did what mine did, all you are left with is an antenna housing with a plugged screw hole..
good luck

Posted on May 03, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How can I repair a98 Honda Civic 4 door. Moon roof wont close all the way. Seams to be on an angle when closing. What can I do?

Can you help it along by lifting one side? Or by tugging one side down?

I'm betting it has plastic slide bushings, and one has worn completely out. Getting it out & getting a replacement one in will be a challenge... there may be quite a lot to take apart & put back together.

Jul 29, 2014 | 1998 Honda Civic

1 Answer

Problem: front corner base of camper seam is pulling apart. Each time we use the camper the corner seam pulls apart a little farther, now when closing up the camper the roof does not seat over that corner....

The worst occurrence with a camper is water intrusion. This causes de-lamination of the fiberglass to the mounting
board. One has to check any and al places where water may enter through cracks in caulking and also screws. Most campers are attached with screws and then the screws are covered with a plastic covering to hide the screws. If water gets behind and around these screws, it
will follow the threads inside the camper in a wicking manner. Only way to stop it is to remove the screws and put caulking in the screw hole before replacing the screws.
Also look for any cracks on roof or in caulking no matter how small - water will find its way inside. Best caulk to use is one that is self leveling and stays soft. Do NOT use RTV
Silicone Caulk! it collects dirt and will eventually pull off.
I recommend same caulk used by mfg of the rubber roof.
Caulk will not stick to anything wet - has to be completely dry and clean.

Feb 07, 2018 | Cars & Trucks

1 Answer

Loud pop coming from roof area possible around sun roof

remove the headlining then squirt some foam filler behind the support bars ,i think they may be flexing causing the noise as this sort of fault is common the rover 75

Nov 12, 2012 | 2006 Cadillac DTS

1 Answer

Where do rover fit the cd multi changer in a rover 75 as mines missing.

the 6 cd multichanger fits either in the glove box or on brackets in the boot, model is alpine cmh s630comes with fixings, all other interfaces are inside boot, behind bumper under hard black plastic cover. hope this helps

Jan 15, 2012 | 2000 Rover 75

1 Answer

Replacing rear bulbs on rover 75 tourer

With the trunk open, look along the side of the lens assembly and you should see some screws, remove those and you can pull the assembly out. Then twist the sockets on the back of the assembly to free the bulbs

Sep 16, 2009 | 2002 Land Rover Freelander

1 Answer

There is a puddle of oil behind the throttle plate in my 97 land rover discovery.why? there is a breather hose that goes from the valve cover to the mantafold plenum is there supposed to be a pcv valve or...

My 96 Discovery has a plastic baffles inside the valve cover port that connects to the hose. If it got brittle and cracked, then oil could leak by. Its cheap and easy to replace, along with the hose. There is a second hose on the other side to replace as well. Land Rover was proud to pass emissions standards without using exhaust gas recirculation (EGR). The whole system is sealed, so all the air entering the engine is being metered by the Mass Air Flow (MAF) sensor, unless your breather hoses crack and leak. Unfortunately, oil in your location might also indicate other engine trouble, such as worn piston rings (causing pressure in the crankcase). I would try replacing the plastic baffle piece first.

Aug 30, 2009 | 1997 Land Rover Discovery

1 Answer

Freelander 2000, removing the soft top

The seams should slide off just pull from the bottom of the seams, there is a section of the plastic guide missing where they come out, a bit wd40 should ease them out if there tough to pull.

Mar 25, 2009 | 2002 Land Rover Freelander

3 Answers

Split in my rear plastic window audi cabriolet 1996 2.6 v6 HELP!!

The window can be replaced just go to a foreign car used auto parts or junkyard or go to your nearest dealer for your car and have it done.

Jan 02, 2018 | 1996 Audi Cabriolet

1 Answer

Removal of the engine gaurd

unfortunatley there are about 10 bolt and screws to remove the aluminium guard along with the plastic--I have just done this and had trouble with siezed set screws--I have now split the unit so that when draining engine oil only the plastic shield is removed

Jan 11, 2009 | 2004 Land Rover FreeLander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rover Experts


Level 3 Expert

77499 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

ray gallant

Level 3 Expert

48512 Answers

Are you a Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides