Question about Chrysler Cars & Trucks

Open Question

Instructions for changing a timing belt on chrysler pacifica

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

chargerhp
  • 813 Answers

SOURCE: I don't know how to change the time on my Chrysler

If it's the round on near top of dash take a ball point pen and push the round circle next to the clock. If it's the one in the radio push button that says time then push the h button one the m button with ball point pen just like the top on before the display changes away from the time of day

Posted on Feb 25, 2010

  • 47 Answers

SOURCE: 2006 Chrysler Pacifica serpentine belt routing

here are a couple diagrams...
1e7d361.jpg

011a835.jpg

If you need anything else, let me know.

Posted on Mar 19, 2010

  • 1757 Answers

SOURCE: i am installing a timing belt on a 2004 chrysler

Click on the following: free, direct Link. It has several Diagrams including the Serpentine Belt Diagram for your 2004 Chysler Pacifica 3.5L DOHC V6. It has the Instructional and Directional Diagrams that will help you.

http://www.2carpros.com/car_repair_information/year/2004/make/chrysler/model/pacifica/2004_chrysler_pacifica_drive_belt_routing_diagram.htm

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench (See Diagram in Link: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Posted on Apr 03, 2010

  • 1024 Answers

SOURCE: serpentine belt routing for 2004 chrysler pacifica

here it is

98c85ed.gif

Posted on Apr 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After changing the water pump and timing belt on a 2005 Chrysler Pacifica 3.5 the engine will idle but surges when I accelerate. There is no codes being shown.


i'd advise rechecking the timing belt positioning again , surging can be a symptom of timing being out and i would'nt expect any codes if its the belt timing, as is set up manually and not monitored by the PCM

Jun 11, 2015 | 2005 Chrysler Pacifica

3 Answers

If a water pump in a 2004 chrysler pacifica with 3.5l is leaking would it run out right below the crank pulley


This is common water pump failure on the pacifica, the bearings start to leak.
Since it is ran off the timing belt it is very common for the coolant to eat away at the timing belt, once that belt breaks your engine is destroyed.
This is not a repair that is OK to put off, replace the water pump timing belt and tensioner

Sep 20, 2014 | 2004 Chrysler Pacifica

1 Answer

My 2004 chrysler pacifica is idling hard after i had timing belt changed and check engine light i on


make sure the timing belt was put on correctly,scan for fault and diagnose it may lead to that

Jul 24, 2012 | 2004 Chrysler Pacifica

1 Answer

When do one change the timming belt on a 2004 Chrysler Pacifica


The timing belt manufacturers usually recommend 60k; but the vehicle mfr may 80k. So its safe to say around 60-80k miles.

Aug 30, 2011 | 2004 Chrysler Pacifica

1 Answer

I CHANGED THE TIMING BELT ON A 1997 CONCORDE 3.5. THE BELT WAS BROKE SO HOW DO I KNOW IF THE TIMING IS RIGHT


this forum link will help you http://en.allexperts.com/q/Chrysler-Repair-807/2008/4/timing-belt-pacifica-3.htm the 3.5 has lots of little things you can and can't do to it as far as turning in a certain direction, you'll see

Jul 13, 2011 | 1997 Chrysler Concorde

1 Answer

Replacing a water pump on a 2004 pacifica


Release fuel pressure.Remove neg battery cable. Drain cooling system.Remove front cover.Remove timing belt. Remove water pump. Remove timing belt tensioner and slowly compress in vice. Install water pump then install tensioner and belt. timing belt runs water pump!

Sep 02, 2010 | 2005 Chrysler Pacifica

2 Answers

I am installing a timing belt on a 2004 chrysler pacifica and i need help!


Click on the following: free, direct Link. It has several Diagrams including the Serpentine Belt Diagram for your 2004 Chysler Pacifica 3.5L DOHC V6. It has the Instructional and Directional Diagrams that will help you.

http://www.2carpros.com/car_repair_information/year/2004/make/chrysler/model/pacifica/2004_chrysler_pacifica_drive_belt_routing_diagram.htm

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench (See Diagram in Link: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 03, 2010 | 2004 Chrysler Pacifica

1 Answer

2006 Chrysler Pacifica serpentine belt routing


here are a couple diagrams...
1e7d361.jpg

011a835.jpg

If you need anything else, let me know.

Mar 15, 2010 | 2006 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...