Question about Volvo Cars & Trucks

Open Question

I need help with thhe crankshaft pulley timing mark on my s60 volvo T3, we changed the timing belt now it wont start, no spark

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 28 Answers

SOURCE: crankshaft pulley timing marks

the red mark is where the timing is supposed to be after u have bypassed the electronic advance.the first white line on the left is tdc.
thanks for useing fixya

Posted on Aug 18, 2008

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

ewashmidas
  • 362 Answers

SOURCE: Replacing Timing Belt on 1993 WA Ford Festiva

Howsb5b35f0.png this...

Posted on Feb 01, 2009

  • 17 Answers

SOURCE: Replace timing belt on Volvo S60

There is no room for error...... Zero clearance. If off one tooth it can and will bend valves. if you are one that just feels the need to get alittle dirty or just can't pay for the service, then get out your Haynes out and turn to .....Tune up, and look at replacing timming belt. Get a cam gear tool that locks them into place so as that they will not move when u have them lined up. make sure they are lined up with marks as said in book. then make sure crank as well as all marks are lined up acordingly. make sure belt marks are lined up with everything. i would reccomend using a volvo belt though cause it will have all the marks on it.However other company's make good quality belts also at a fraction of the price. So it is really up to you.
Good thing when doing timming belt is to also change out your timming belt tensioner. YES do this it will save you a engine in the long run. it is a moving part that will go bad, it will freeze up and snap timming belt. rip out teeth in thebelt and bend valves. So as a gen rule...When you change timming belt, Change belt tensioner at same time since you cant just change tensioner without changing or getting timming belt off. Remember to use your HAYNES. It is your friend and will save you money in the long run. Good luck... Hope this helps you.

Posted on Apr 08, 2009

SOURCE: vw golf 1.4 16v after changeing timing belt car

The timing could be 180 degrees out you will have to do it all over again. Bring #1 cylinder upto TDC check the distributor rotor arm that it is pointing to #1 plug wire, It is important that the cams are on the intake stroke and not on the exhaust stroke. The crank is no big deal just make sure the marks are lined up.

Posted on Sep 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Volvo S60 T5 2002. I have not done the maintenance after the 100,000 miles. Can you tell me which prts I need to change?


There are a few things that need to be done, first the timing belt and waterpump if this engine has one most do, so for this you would need a waterpump timing belt kit with pulleys, next is a complete tune up, spark plugs ,wire if eng uses if not then coil boots, air and fuel filters cabin filter, pcv valve, a fuel system cleaning which is done by machine at a shop called a motor vac service. then check fan belt , flush cooling system, coolant needed.and then the rest of the service is a lot of checking like brake, suspension , exhaust etc,hope this helps.

Dec 24, 2010 | 2002 Volvo S60

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

Timing marks on a 2000 volvo v40 1.9t crank and cam marks


Timing belt alignment markings


9c6ff12.gif

Here is all the tech info for removing and replacing....hope this helps you:

4-Cylinder Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Right hand engine cover
    • Cover over the right headlamp
    • Accessory drive belt
    • Front timing cover
    • Servo reservoir
  3. Position Volvo lifting beam 999 5006 or equivalent slightly in front of the front lifting eyelet for the engine. Use Volvo lifting arm 999 5383 or equivalent and Volvo lifting hook 999 5460 or equivalent to raise the front of the engine a few millimeters.
  4. Remove or disconnect the following:
    • Right-hand engine mount
    • Right front wheel
  5. Turn the crankshaft until the markings on the crankshaft and camshaft pulley correspond. Turn the crankshaft a further 1/4 turn clockwise and then back again until the markings correspond. The markings are illustrated. Remove the upper timing cover.
  6. Slacken off the center screw for the belt tensioner slightly.
  7. Turn the tensioner clockwise to 10 o'clock.
  8. Remove or disconnect the following:
    • Air baffles
    • Lower belt cover
    • Timing belt


To install:
  1. Turn all the pulleys listening for bearing noise. Check to see that the contact surfaces are clean and smooth. If the tensioner pulley lever or idler is seized, replace it.
  2. If replacing with a new idler pulley, tighten to 18 ft. lbs. (24 Nm).
  3. If replacing tension pulley, screw into place using the center bolt by hand. Ensure that the tensioner fork is centered over the cylinder block rib. Ensure that the Allen hole on the eccentric is at "10 o'clock".
  4. Install the timing belt in the following order:
    1. Around the crankshaft sprocket
    2. Around the idler pulley
    3. Around the camshaft sprockets
    4. Around the water pump
    5. Onto the belt tensioner
  5. Carefully turn the crankshaft clockwise until the timing belt is tensioned. The belt must be tensioned between the intake camshaft pulley, the idler pulley and the crankshaft
  6. Hold the belt tensioner center screw secure. Turn the belt tensioner eccentric counter-clockwise until the tensioner indicator passes the marked position.
  7. Then turn the eccentric back so that the indicator reaches the marked position in the center of the window and tighten the center bolt to 15 ft. lbs. (20 Nm).
  8. Press the belt to check that the indicator on the tensioner moves easily.
  9. Install or connect the following:
    • Lower belt guard
    • Air baffles
    • Upper timing cover
  10. Turn the crankshaft two turns. Check that the markings on the crankshaft and camshaft pulley correspond.
NOTE Check that the indicator on the belt tensioner is within the marked area.

  1. Install or connect the following:
    • Lower timing cover
    • Front timing cover and tighten to 9 ft. lbs. (12 Nm)
    • Accessory drive belt
    • Engine mount and tighten to 49 ft. lbs. (67 Nm)
    • Servo reservoir. Tighten bolts to 37 ft. lbs. (50 Nm).
    • Front wheel
    • Right hand engine cover
    • Cover over the right headlamp
    • Negative battery cable

May 04, 2010 | 2000 Volvo V40

2 Answers

I am planning to replace the timing belt on my daughter's 95 Corolla and was wondering what I need to align where before removing the belt eg How do I find TDC? Camshaft pulley and Crankshaft pulley...


TDC is top dead center/ remove spark plug on cylinder no. 1/ rotate the crankshaft pulley using a socket wrench and power handle and check if the piston on your cylinder no. 1 reach the top center that is TDC/ remove timing belt cover and locate a synchronized marking on your camshaft and crankshaft pulley/ remove old timing belt/ install a new one but make sure that the mark on your camshaft and crankshaft is perfectly synchronized before putting the cover/ manually rotate the crankshaft pulley again and see if it rotates 360 deg. freely then you can be sure you did the job correctly.

Apr 06, 2010 | 1995 Toyota Corolla

1 Answer

S60. 2.4T removing and replacing timing belt


remove auxilary belt remove one bolt from timing belt cover remove cover turn engine to tdc using socket on crank nut check cam pulleys lined mark with white paint or tipex remove 4 bolts on crank pulley then centre pulley nut use impact gun prise of pulley check all marks still lined up buy or borrow universal cam sproket lock tool this is important to stop cams moving when belt of release tensioer remove belt chek water pump for leaks and wear fit new tensioner then new belt keep tight on non tension side feed over sprokets tension belt to align pointer on tensioner turn engin 2 times re check timing marks fit all parts removed

Nov 23, 2009 | 2001 Volvo S60

2 Answers

How to changing a timing belt on a 2000 ford focus SE


FOR A 2.0 SPI ENGINE:
Removal
  1. Remove the accessory drive belt.
  2. Detach the coolant expansion tank.
  3. Remove the bolt and position the expansion tank to one side. Detach the power steering reservoir and position to one side.
  4. Remove the right-hand front wheel and tire.
  5. Remove the crankshaft pulley/vibration damper.
  6. Lower the vehicle. Disconnect the ignition wires from the spark plugs.
  7. Remove the two ignition wire separators from the valve cover.
  8. Remove the spark plugs. Place a jack with a wooden block under the oil pan and raise slowly until the front engine mounting is free from strain.
  9. Remove the engine front mounting. Remove the timing belt cover.
  10. Remove the engine front mounting bracket. Align the timing marks.
  11. Remove the timing belt. Use an 8 mm Allen wrench and turn counter clockwise 1/4 turn.
  12. Insert a 3 mm (1/8 inch) drill bit to lock the timing belt tensioner in place.
  13. Remove the timing belt.

Installation
  1. Check the alignment of the timing mark on the crankshaft timing belt pulley.
  2. Check the alignment of the timing mark on the camshaft timing belt pulley.
  3. Install the timing belt. Install the timing belt over the pulleys in a counter clockwise direction starting at the crankshaft.
  4. Keep the belt span from the crankshaft to the camshaft tight while installing the timing belt over the camshaft.
  5. Remove the 3 mm (1/8 inch) drill bit to release the timing belt tensioner.
  6. Turn the crankshaft at least two turns in clockwise direction to TDC position for cylinder one.
  7. Check the alignment of the timing marks.
  8. If the alignment is not correct repeat the previous steps. Install the engine front mounting bracket. Install the timing belt cover.
  9. Install the engine front mounting. Remove the jack. Install the spark plugs.
  10. Push on the spark plug connector until it engages.
  11. Raise and support the vehicle. Install the crankshaft pulley/vibration damper.
  12. Position the drive belt on the crankshaft pulley.
  13. Install the right-hand front wheel and tire.
  14. Install the power steering reservoir.
  15. Install the coolant expansion tank. Install the accessory drive belt.

Nov 10, 2009 | 2000 Ford Focus

1 Answer

Needing schematics for timing belt on a 2000 se


Removal & Installation

2.0L Engine
  1. Remove or disconnect the following:

    Negative battery cable Spark plugs Catalytic converter Right front wheel Right inner splash shield Accessory drive belt and idler pulley
  2. Rotate the crankshaft to Top Dead Center (TDC) and install Crankshaft TDC Timing Peg T97P-6000-A.
  3. Rotate the crankshaft clockwise against the peg.
  4. Remove or disconnect the following:

    Water pump pulley Valve cover Crankshaft pulley Timing belt covers
  5. Install Camshaft Alignment Timing Tool T94P-6256-CH into theslots of both camshafts at the rear of the cylinder head to lock thecamshafts into position.
  6. Loosen the timing belt tensioner bolt and relieve the tension onthe timing belt by disconnecting the tensioner tab from the timingcover back plate.
  7. Remove the timing belt.

    0900c152801e2a75.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Crankshaft alignment position-Ford 2.0L (VIN 3) engines


    0900c152801e2a76.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Placement of Camshaft Alignment Timing Tool T94P-6256-CH-Ford 2.0L (VIN 3) engines


    0900c152801e2a77.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Timing belt tensioner index marks-Ford 2.0L (VIN 3) engines

To install:

NOTE Always replace the timing belt after loosening or removing it.
  1. Install the timing belt.
  2. Engage the timing belt tensioner tab into the timing cover back plate.
  3. Adjust the timing belt tensioner until the index marks are aligned. Tighten the tensioner bolt to 17-20 ft. lbs. (22-28 Nm).
  4. Remove the camshaft alignment tool and the crankshaft TDC peg.
  5. Install or connect the following:

    Timing belt covers Crankshaft pulley. Tighten the bolt to 81-89 ft. lbs. (110-120 Nm). Valve cover Water pump pulley Accessory drive belt and idler pulley Right inner splash shield Right front wheel Catalytic converter Spark plugs Negative battery cable
  6. Start the engine and check for proper operation.

Apr 08, 2009 | 2000 Ford Contour

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

2 Answers

Timing belt replacement


This is the timing belt replacement procedure to 1999 Vovlo V70
with the B5254s engine

1) Lift power steering and anti-freeze resevoirs slightly and disconnect electrical connector for antifreeze sensor. Then carefully lift both resevoirs and position it on top of the valve cover.

2) Relieve the tension from the serpentine belt tensioner pulley and remove the serpentine belt.

3) Remove the screw holding the plastic timing belt cover and carefully remove the cover.

4) Locate the timing marks on the camshaft pulleys. I highlighted the marks with paint to make them easier to see. I took a dab of white touch up paint and put it on each mark, then waited a minute and then wiped the excess paint carefully, leaving a white line for the mark. The mating marks for the cam gears is on the upper cam gear cover. The marks are rectanular cutouts on the underside of the cover. I was unable to line up the marks unless standing on my head so I extended the marks to the outside of the cover with a white painted dot. This trick made life much easier.

5) Reinstall the timing gear cover.

6) Place a 32mm socket on the crankshaft pulley and connect a breaker bar to the socket. Slowly rotate the engine crankshaft (clockwise) until the camshaft timing marks are aligned with the marks on the gear cover. (I preferred to do this job with the spark plugs installed. I found it easier to keep the engine in time by using the engine compression).

7) Remove the vibration damper by removing the 32mm nut and remove all of the 10mm screws. Carefully pry the pulley from the shaft. There is an alignment pin which allows the pulley to be installed only one way. With the vibration damper removed you can now check the timing alignment with the crankshaft and it's witness mark.

8) Remove the small timing belt shield from the underside of the crankshaft. This shield is helt in place with 2 screws.

9) Loosen the ttiming belt tension and remove the old timing belt.

10) This is a good time to check the waterpump for any signs of wear or leaks. Mine was leaking after 101,000 miles. I also replaced the tensioning pulley and used Volvo OEM parts. (The old Volvo parts lasted 100,000 miles, that is good enough for me).

11) Reverse the procedure for installing the new timing belt.

12) After the belt is installed and properly tensioned, put the breaker bar with the 32mm socket onto the vibration damper and rotate the engine (clockwise) slowly until your timing marks are again aligned. If they are not, remove and reinstall the belt. Don't get frustrated just think of all of the money you have saved by doing this job yourself.

dbea7d9.jpg68d3133.jpg

Aug 10, 2008 | Volvo 740 Cars & Trucks

4 Answers

How to replace timing belt for volvo xc90 2.5 turbo?


hi ineed helf to set cam shaft timing on 2003 volvo xc 90 t9

Jul 08, 2008 | 2003 Volvo XC90

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...