Question about Cars & Trucks

Open Question

Small metal shield has fallen off the bottom of my w 18 workhorse chassis on my motor home. I can't find where it goes. Any ideas?

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2002 Workhorse chassis RV hazard flasher doesn't work

I am looking for a locking gas cap for my 2005 Bounder 36Z. This motorhome has a Workhorse chassis. Can you help me locate the part number and a dealer near Newberg, Oregon?

Thank you.

Sharon Bladow
503 554-1281

Posted on Aug 15, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Motor home on a 8.1 GMC Workhorse Chassis. Issue:it is shutting off while driving. If u pull over, put it into park, turn the ignition off it will restart fine. Any ideas of cause?


I once had a small piece of paper floating in the gas tank that would wrap itself around the fuel pick up tube and stop fuel flow. Stop it....paper floats again .... good to go until it happened again. Have a look in the fuel tank. It drove me nuts until I finally had a look.

Sep 13, 2016 | GMC Cars & Trucks

1 Answer

New replacement Blower does not have a ground wire, existing blower does, will the new part work without a ground wire?


Are you talking about hvac blower motor? How many pins on the blower connector, should be two, one is voltage, the other is ground.

If the new blower pigtail has only one wire, maybe it grounds through the chassis? You could use a redundant jumper wire for ground if your worried. One end of the wire goes to blower motor mounting screw, make sure it is touching bare metal, the other end of wire goes to bare metal spot on chassis.

What is year--make--model of vehicle?

Nov 03, 2015 | Cars & Trucks

1 Answer

Need the key code for a 2001 chevrolet isata touring sedan motor home lost my keys for ignitiion


Only a dealership can help you, that info is not available to the general public, it is vehicle specific.

Aug 21, 2014 | Cars & Trucks

1 Answer

Where is the freeze plug located at on a 1989 cressida


The freezer plug is located on the left side of the motor under the exhaust manifold towards the back.I think its visible if you take off the metal heat shield that's on the manifold or maybe from the bottom if you lift the car.If its not leaking from there than it could be coming from the back of the motor. There are hoses, a EGR cooling plate and metal water lines on the motor.

Jul 09, 2014 | 1989 Toyota Cressida

1 Answer

1999 dodge durango ticking from flywheel or torque converter


Sounds like the metal shield between motor and transmission it happen to my durango I thought it w as torx converter bolt coming loose It was my flex plate bent

Jun 20, 2012 | 1999 Dodge Durango

1 Answer

I have a 2001 winnebago on a workhorse chasis. with 4L80-e transmission that dont lock when put into park


There is a fuse for the auto park that you need to check and also make sure that the reservoir under the winnebago isn"t leaking. There is a green switch under the motor home on the hydraulic unit for the brake that goes bad quit often.

Sep 23, 2010 | Chevrolet 3500 Cars & Trucks

2 Answers

How to pullout starter on 2000 gmc sierra 4 by 4


4.3L Engine
  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
  1. Install or connect the following:

    Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

    c5acb83.jpg
    Fig. Exploded view of the starter motor-4.3L engines.


  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
Install or connect the following:

Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

a557bbc.jpg
Fig. Exploded view of the starter motor-4.3L engines.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2000 GMC Sierra

1 Answer

Knocks alot is it the motor or is there a bolt in the transmision bell


Look under the car to see if there is a loose heat shield around the exhaust pipe/catalytic converter area. Look right between the front seats (under the car). The front portion normally rusts away from the bolts holding it in place. This is like a ****-shell part - the top half or bottom half vibrate against the catalytic converter (sounds like knocking). Dealer can fix for about $100. You can fix for about $5.

Get a small piece of fiber glass fabric (auto store) and fold nicely and fit betwen the loose parts. Then get 3 pieces of 10 gauge copper about 18 inches long and wrap around the entire heat shield and twist tight. This will stop the vibration and last a long time in harsh environmental conditions. Do not just drive without the heat shield. You can melt your carpeting and start fires if you ever drive on grass.

Nov 19, 2009 | 2002 Isuzu Trooper

1 Answer

2002 Workhorse chassis RV hazard flasher doesn't work


I am looking for a locking gas cap for my 2005 Bounder 36Z. This motorhome has a Workhorse chassis. Can you help me locate the part number and a dealer near Newberg, Oregon?

Thank you.

Sharon Bladow
503 554-1281

Aug 14, 2008 | GMC R3500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...