Question about Cars & Trucks

1 Answer

How to reverse ailerons - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,673 Answers

On what?

Posted on Apr 26, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Mitsubishi aileron won't start turn over nothing lights work n eavrything already have checked the starter it's fine what other thing could it be


I HAVE AN ECLIPSE. Sometimes it the little stuff so lets try something.
  1. Your lights work ok but no start that's because your lights do not need 650 cold cranking AMPS to work.so:
  2. disconnect your battery cables. clean the posts and cables were they go over the posts till there silver. Use wire brush.
  3. reconnect and make sure they are tight.
  4. check for 12 or more volts at battery
  5. try a start
  6. if not clean and tighten other ends of cables and other wires to solenoid.
  7. try a start
  8. if not check for power 12 volts at the starter
  9. if not check the line power from the key
Hope this helps Mike

Mar 02, 2016 | Mitsubishi Cars & Trucks

1 Answer

How do i add transmission fluid? Why won't it stay in reverse gear?


VWVortex.com - 1997 MK3 Jetta 2.0L 8v 5spd Reverse Gear Problem ...

forums.vwvortex.com > ... > Golf III & Jetta III
Dec 8, 2006 - 25 posts - ‎18 authors Hello, I have a 1997 MK3 Jetta 2.0L 8v 5spd my reverse gear is ... car in reverse- always, not even a little rolling, i have found that vw trannys r .... Member MKIII_96'sAvatar .... misalignment and problems with the transmission staying in gear. .... You can ask a hundred ways, but it won't change the answer/s. Won't go into 5th gear.
25 posts
Apr 17, 2009
1996 Jetta 2.0 5spd - No Reverse
10 posts
Jan 5, 2009
Car won't go into REVERSE!!! WTF? Any ideas?
25 posts
Nov 14, 2008
Transmission Shift Lever Stuck in Park - or, Key ...
25 posts
Nov 13, 2005
More results from forums.vwvortex.com

Volkswagen Cabrio Questions - pops out of reverse ...

www.cargurus.com > Questions > Volkswagen > Cabrio
CarGurusMar 26, 2012 - My 96 Cabrio pops out of reverse then makes grinding noise. ... worse case is the reverse gear has a few teeth missing which is a common problem in 97 and older ... Won't stay in reverse 1 answer ... 1991 Volkswagen Passat.

Oct 27, 2015 | 1996 Volkswagen Jetta

1 Answer

We have a 2011 ford f350 and are trying to t/s the reverse lights. we checked the fuses. what else might it be. we cant find a diagram to the wiring.


In the BJB - battery junction box under the hood ,is a reversing lamp relay. Check it or try a known good one !an check fuse F70 10amp in the BJB .

Reversing Lamps

The reversing lamp system consists of the following components:

  • Rear lamps
  • Reversing lamp switch
  • PCM
  • BCM

When the transmission is placed in REVERSE (R), the BCM provides voltage to the reversing lamps. The reversing lamps are located within the rear lamp assemblies.
When the transmission is in REVERSE, the PCM (gasoline engine) or the Transmission Control Module (TCM) (diesel engine) sends a message over the High Speed Controller Area Network (HS-CAN) to the Body Control Module (BCM) indicating the transmission is in REVERSE. The BCM provides voltage to the reversing lamps when it receives the message that the transmission is in REVERSE and the ignition is in the RUN state. You could have a transmission range sensor problem , check to see if it is adjusted correctly ! Need to have a scan tool to make sure the BCM is receiving signal from the PCM . This is complex for someone who doesn't deal with or know about serial data communications ! All it is ,is electric inputs to a control module, then the control module configures it into data bits an bytes 1's an 0's then sends it out on the Data bus. The module that needs this info reads it an turns on the lights.This system can set codes in the bcm ,leading to a problem.

  • DTC B1277:11 (Reverse Lamp: Circuit Short To Ground) - a DTC that sets when the BCMdetects a short to ground from the reversing lamp output circuit.
  • DTC B1277:15 (Reverse Lamp: Circuit Short To Battery or Open) - a DTC that sets when the BCMdetects an open from the reversing lamp output circuit.
  • Could set codes in the PCM - powertrain control module for a transmission range sensor problem !
  • Jan 28, 2015 | Ford F-350 Cars & Trucks

    1 Answer

    The reverse gear is fine it's the reversing lights that go out when it goes in to reverse gear


    You say that the reverse lights go out when reverse gear is selected! At what point are they on? Before reverse is selected?

    Oct 25, 2014 | Cars & Trucks

    1 Answer

    95 dodge neon wont go into reverse


    Reverse clutch pack problem .

    Mar 11, 2017 | Cars & Trucks

    1 Answer

    Have a 94 New Yorker when I put it in reverse I get a red R on the PRNDL and don't have reverse all other gears are green and work. What might be causing this?


    the reverse clutch in the trans is after failing.there are two clutch packs in trans for reverse,low/reverse and reverse clutch in overdrive unit,so where you have all foward gears the low/ reverse is ok the reverse clutch in od unit is most likely culpret

    Aug 08, 2009 | 1994 Chrysler New Yorker

    1 Answer

    2005 Pathfinder no reverse lights


    On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

    Apr 20, 2009 | 2005 Nissan Pathfinder

    1 Answer

    Reverse is gone on 1995 chevy blazer s10-goes forward just fine


    reverse clutch went out rebuild transmission

    Feb 21, 2009 | 1999 GMC Jimmy

    1 Answer

    NO REVERSE LIGHTS REAR PARK SENSOR WHEN REVERSE SELECTED


    On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced. The switch is just plug and play

    Jan 28, 2009 | 1999 Mercedes-Benz E-Class

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    23 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...