Question about Cars & Trucks

Open Question

Hi I am looking for Mongoose 04A15C Raider Truck parts! One is the switch pedal foot and the other is the male connector of the battery that plug in the charger!

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 9 Answers

SOURCE: No brake lights on 96 yukon

The brake fuse #1 is located inside the truck below the steering column. I am assuming you have verified there is 12v power at the fuse & thru the brake lamp switch (orange wire power in & white wire power out, when pedal depressed) at all times. After the brake lamp switch , power goes (white wire) to the Turn signal/hazard lamp switch & out (dark green wire-rt brake lamp & yellow left brake lamp)

Posted on Feb 16, 2009

Ad
  • 53 Answers

SOURCE: break lights stay on

the switch or due to weather the wires might be damaged, but it's a short...you might want to check into getting it to stop stayin on as the brake light lights up with others in a sequence for diagnostic codes and troubleshooting engine problems.....good luck..shia

Posted on May 23, 2009

  • 19 Answers

SOURCE: Brake Lights do not come on.

i am assuming the lights work while connection is engaged. simple secure the two parts of the connection together even if you have to with gaffer tape.

Posted on Nov 24, 2009

  • 566 Answers

SOURCE: electronic connector for brakes on Hyundai Accent

hi from uk the part you mention is the brake stop light switch it has a plug on 2xwire plug it operates by as pedal is pressed the plunger of switch moves out and connects the 2xwire circuit and so brake lights operate this switch simply unscrews from the pedal box/carriage after plug removed then the new switch screwed in place and with b/pedal off the switch is screwed to a point that if you press pedal down approx 1/2 " the switch plunger moves out and b/lights come on this is trial/error untill you are happy with the pedal movement down till lights operate SIMPLE ! hope this helps?

Posted on Nov 28, 2009

Testimonial: "thanks for the feedback, now all i need to find out is if I can buy this part? "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Male plug burned in light switch


Automotive Electrical Connector Pigtails, Terminals, Tools ...

www.repairconnector.com/
HEADLIGHT And DIMMER SWITCH CONNECTORS ... Electrical connectors are one of the most overlooked reasons for engine and starting problems on a car, truck, ... GM 4 Pin Oil Pressure Switch Repair Connector $14.99 ... Male Tab Quick Disconnect .250 Spade Terminal Crimp 100 Pack 12 10 AWG $24.75 $14.99.

Headlight Switch and Harness Connector Replacement - FSB Forums ...

www.fullsizebronco.com/.../343281-headlight-switch-harness-connector-...
Dec 30, 2014 - Burn marks were also apparent on switch terminals. .... In an oldertruck, the headlight switch connector is the first place I would look at when .... If I ever find a good trustworthy source for male headlight plugs, I might try making some..... Comparing The 3 High-Paying Miles Rewards CardsLendingTree.

How to Diagnose and Repair a Broken Auto Light Socket ...

www.familyhandyman.com > Skills

Jan 06, 2016 | Cars & Trucks

1 Answer

How do I get my breaks light to turn off on my 2002 dodge 1500 pick up


the brake light switch is proberly over adjusted if both lights are on ,dont panic easy fix the switch is located on the top of brake pedal so look under dash at pedal you will see two wire to a connector remove this connector the lights should go out , then twist the switch, that the connector was in , anti clockwise 360 degrees plug back in if lights come on repeat the adjustment of switch until lights are off and only come on when pressing pedal let me know how you get on

Apr 29, 2014 | Cars & Trucks

1 Answer

Break light


1st things first, check your bulbs. If they are good, check fuses under the hood. Then go to the brake switch located way up on top of the brake pedal. Check the male connector that plugs into the white switch. The wire is kind of short, and will sometimes melt from all the movement. I chased my problem down for a month, was the male connector on top of the brake switch that burnt. May need to cut the connector off and buy a new one with pigtails and wire it back up with longer wires.

Apr 01, 2014 | 1998 Oldsmobile Bravada

1 Answer

My window washer switch seems to be broken. I recently filled it with washer fluid, but it wouldn't spray or wipe the winshield. Tonight, for an experiment, I hit it with the palm of my hand and it...


the washer pump is inside the bottom of the reservoir. If it worked on being smacked, I assume someone was inside holding the button, then I would take a shot at pulling the pump's electrical connector plug off and giving the male and female parts of the connector a good dousing with WD40 or any other moisture replacing anti-corrosive solvent. You could simply have a bad connection.

Sep 30, 2010 | 2007 Mitsubishi Raider LS

1 Answer

Electronic connector for brakes on Hyundai Accent


hi from uk the part you mention is the brake stop light switch it has a plug on 2xwire plug it operates by as pedal is pressed the plunger of switch moves out and connects the 2xwire circuit and so brake lights operate this switch simply unscrews from the pedal box/carriage after plug removed then the new switch screwed in place and with b/pedal off the switch is screwed to a point that if you press pedal down approx 1/2 " the switch plunger moves out and b/lights come on this is trial/error untill you are happy with the pedal movement down till lights operate SIMPLE ! hope this helps?

Nov 28, 2009 | 2003 Hyundai Accent

2 Answers

How do you change a brake light switch on an 1998 chevy truck


Hi,
I don't know about your specific truck, but most cars and trucks have the switch activated right from the braking pedal arm. If you look under the dash towards the upper part of the brake arm, you might spy a switch that activates when you move the arm. It should be easy to identify... and replace, if you like standing on your head!
I hope this helps... Good luck!

Oct 13, 2009 | 1998 Chevrolet C1500

9 Answers

My brake light for my frontier truck will not go out after I turn off the engine. What and where do I buy a switch for the problem? I have to take off the batteries terminal to turn the lights off and...


DON'T REPLACE YOUR BREAK LIGHT SWITCH YET...

the 98 frontier break arm (what the pedal is attached to) has a MANUFACTURED "hole" through it that will allow the plunger of the break light switch to pass right thru. There is supposed to be a rubber "button" snapped into this hole, however, over time, dry rot and age will cause it to fall out. When this "snap in" button falls out, your break lights will stay on till the battery dies. This is another shining example of DTF engineering. (design to fail) Most cars now are filled with these little parts and they're purpose is to generate revenue.

Your break switch probably works.
1. look in the floor board for the button that fell out, it's about the same size as a button off your shirt.
2 Slide your hand up the break pedal arm till you find the "hole" I'm referring to. (you'll know it when you feel it)
3 Tape the damn button back into the hole with electrical tape, or tape a shirt button over the hole. that will work for a little while.
** remember ** if you are driving with break lights in this condition (on all the time)...no one knows when you're really stopping!!!

you can get a snap in rubber grommet to replace it at most hardware stores (I don't even want to know what Nissan would charge for this little part.)

**note** replacing it is easy if you start the truck first (power breaks) and have someone hold the pedal while you work on it!

Mar 22, 2009 | 1998 Nissan Frontier

1 Answer

No brake lights on 96 yukon


The brake fuse #1 is located inside the truck below the steering column. I am assuming you have verified there is 12v power at the fuse & thru the brake lamp switch (orange wire power in & white wire power out, when pedal depressed) at all times. After the brake lamp switch , power goes (white wire) to the Turn signal/hazard lamp switch & out (dark green wire-rt brake lamp & yellow left brake lamp)

Feb 16, 2009 | 1999 GMC Yukon

2 Answers

On my 2003 chevy silverado 2500, 3/4 ton pickup both brake lights will not come on. the cargo light does. i have checked the bulbs and they are ok. what could it be, where is it located and do you have a...


Did you look on the brake pedal its self there is a brake light switch located about one foot from the pedal its self look up it might be unhooked or just might need replaced .. thanks jerry holler if you need more.

Feb 01, 2009 | 2003 Chevrolet Silverado Ss

2 Answers

1989 dodge raider starter problem


What would you like to know about your starter?

Oct 16, 2008 | 1989 Dodge Raider

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...