Question about Cars & Trucks

Open Question

Wardrobe slidout cable came lose from slide on the outside and pulled to the inside of the rv

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is causing problem with sliding door handle?


Year/make/model?? A lot of sliding doors implement the use of a cable running from the lock assembly to the inside handle. The cable may be broken causing the door to not open

Mar 08, 2016 | Cars & Trucks

2 Answers

Door only opens from the inside


Take out the lock and you will see the rod which slides up and down to connect to make the lock open it may be worn out have it replaced or tie a wire such as a copper wire from unused electrical wires to tighten the gap which may be lose which as a result does not catch properly to open the lock

Sep 16, 2015 | Cars & Trucks

1 Answer

How to open a 2007 chevy equinox door when outside handle is broken and inside handle wont work?


you need to find a slim jim and slide it down by the window and see if you can pull the lock cable up.

Apr 30, 2015 | 2007 Chevrolet Equinox

1 Answer

2003 Sienna, manual sliding door won't open


"The other door won't open from inside or out."

The 2003 Sienna does use separate cables to open from the outside and the inside.

To fix the door that will not open from the inside or the outside, do this. It is MUCH easier than you may think. It just takes a little time.

Prep: Take the seats out, they just get in the way of working.
Tools: Philips head screwdriver. One larger pry screwdriver or other tool to assist with prying (does not need to be heavy duty)

1. Pull "up" and then "out" on the Cup Holder. It pops off.
2. Remove the screw that is holding the panel to the door. It is located behind the area from which you removed the cup-holder.

Aug 06, 2009 | 2000 Toyota Sienna

1 Answer

Both outside door handles are broken on 1996 Hyundai accent


if you pull out on the window crank just a little you can see the clip get a skinny flat head and push one end of the clip it will fall on the floor so dont lose it then the crank will slide off you should be able to get it from there

Aug 05, 2009 | 2002 Hyundai Accent

1 Answer

2002 Kia sportage spare tire swing arm won't release?


The cable on the KIa is outside near the sapre tire and gets rusted and corroded easily. Also there is a nut which holds the cable securely in a holder so that when you pull on the cable the inside and not the outside of the cable moves. Use WD-40 on the cable, make sure that the cable is secure in the holder and tighten the nut that holds the cable to the frame - the nut is located just below the pull handle, on the outside of the cable itself.

Nov 21, 2008 | 2002 Kia Sportage

2 Answers

Outside sliding door handle?


Yes. It is a difficult job, but not impossible. The hardest part is actually removing the interior door handle. Here are the steps.
  1. remove the interior door handle by pressing the door panel in and prying out the C-ring retainer clip
  2. remove the lock slide switch bezel with 1 screw, then insert a blade on the bottom left of the slider between the slider and bezel, and release the clip, the slide the bezel toward the rear of the vehicle and pull out
  3. carefully unclip the door panel around the lower edge and sides and lift the door panel UP and off
  4. remove the interior lock slide switch with 2 screws
  5. pull back the plastic vapor shield part way to expose the mechanism
  6. there is a cable that runs from the mechanism to the exterior handle, unclip it from the door frame
  7. there is a rod that drops down from the door handle to the mechanism, release the rod from the plastic clip
  8. locate a large (likely black phillips) screw next to the door handle on the EDGE of the door, remove it
  9. locate a 10mm screw on the inside behind the door handle, remove it
  10. locate the final 10mm screw behind the handle through an access hole, remove it (careful not to let it fall inside the door)
  11. the door handle will push out through the door part way- there is another C-clip securing the lock cylinder that will need to be removed, and the lock cylinder can be pushed into the door cavity
  12. pull the door handle through the outside of the door skin- the door handle assembly is still attached inside the door by the latch cable- the cable can be easily removed from the handle assembly to remove it completely
  13. you will likely find that the end of the door handle itself is broken off- don’t buy a new handle! Email me and I will show you my free and possibly better solution that will likely last the life of the vehicle dbonnell1972 at yahoo dot com
re-assembly is the reverse of the removal

Aug 13, 2008 | 1994 Toyota Previa

1 Answer

Auto sliding door


pull inside molding you will see the cables path replace cable he probably broke it

Jun 09, 2008 | 2000 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...