Question about Cars & Trucks

Open Question

I pressed Alt button on remote and now have no channels I turned it off and unplugged it

This morning it's still the same

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 avalanche power keeps on drawing from somewhere and in the morning its dead. I will jump it and it will run fine!


are you leaving anything plugged in, cellphone charger, radar dector, emergency lights, cb, etc, if so unplug all of it that will kill the battery, if not the case, you got a short somewhere

Jan 14, 2013 | 2003 Chevrolet Avalanche

1 Answer

T & C 2001 REMOTE CONTROL PROGRAMMING


ATTENTION: You MUST HAVE one working remote to add one more to the system.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. A chime will sound afer each
additional remote is programmed.

6. Turn the ignition OFF and remove key.
7. Test Remotes.

Sep 17, 2012 | 2001 Chrysler Town & Country

1 Answer

How do you "train" the


Instructions
    • 1 Turn off the engine of the car and press and hold buttons 1 and 3 on the Jeep's transmitter for 20 seconds to erase previous codes. Release them when the display reads "Channels Cleared."
    • 2 Hold your garage-door remote 1 to 3 inches from the Jeep transmitter.
    • 3 Press and hold the open button on your handheld remote and simultaneously press the button you wish to program on the Jeep's transmitter. For example, if you want button 2 to be the one you use to open your garage door, press button 2 while pressing the open button the remote.
    • 4 Release the button once you hear a beep and the display reads "Trained."
    • 5 Press the "smart" button on your garage door motor. This button is usually located on the back or side of the motor near the antenna wire and light lens.
    • 6 Return to your vehicle and press and hold the programmed button in your Jeep for 2 seconds. Release and press and hold the button for another 2 seconds to complete the programming sequence. You will now be able to use the vehicle's transmitter to open your garage door.

Sep 14, 2011 | 2001 Jeep Grand Cherokee

1 Answer

2000Silverado 5.3 Battery light is on in the morning, volts read 11 or 12 normaly read 14,after running a while it goes to 14, twice it feel below 5 volts battey went dead, got new battery,gheck grounds,...


Something is draining your battery overnight and once you start running it, it recharges your battery. If you have anything plugged into your cigarette lighter, unplug them. Unplug anything that you can, like if you have an amplifier for your stereo or anything else. Tonight unhook your negative terminal, and then hook it up in the morning and if it is ok, then you know that is definitely your problem.

Dec 03, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I haven't driven my 2000 Honda CRV in about a week. When I tried to unlock it this morning neither of the remotes would work. I can get into the car manually unlocking the doors but the engine won't...


It sound like the keyfob remotes turn your alarm off on the vehicle. The starter disable part of the alarm is preventing you from starting your car. You will have to get your remotes fixed. Might just need batteries...

Oct 08, 2010 | 2000 Honda CR-V

1 Answer

Factory garage door opener


If this is the 3 button HomeLink Transmitter usually centered overhead above the rear-view mirror, this should work:

While the engine is turned off follow these steps to program up to three channels:
1. Decide which one of the 3 channels (one of the 3 HomeLink buttons) you want to program.
2. Press & hold the desired button through step 3.
3. When the HomeLink indicator light begins to blink slowly(this may take up to 30 seconds), hold your hand-held garage door remote about 1 to 3 inches away from the buttons & then press and hold the button on your garage door remote. Continue to hold both buttons until the indicator light on the HomeLink begins to flash rapidly(this may take up to 90 seconds).

If it still doesn't work, make sure the batteries in your garage remote are not weak, and try again moving the remote back & forth and left & right or turning it upside down while programming.

Also note HomeLink will not work with older garage door openers, especially not with ones manufactured before April 1st 1982.


Feb 18, 2010 | 2005 Buick Rendezvous

2 Answers

My remote key does not work on my 3 series BMW


Very likely the battery is bad, needs replacing. You can try to open it and buy a replacement.

Nov 18, 2009 | 2000 BMW 3 Series

1 Answer

How to program a new remote keyless entry for 2002


1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. Locks will cycle after each additional
remote is programmed.

6. Turn the ignition OFF and remove key.
7. Test Remotes.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Nov 02, 2009 | 2002 Dodge Durango

1 Answer

96 sable wagon keyless entry


Try re-programing the system.
These are the instructions from the service manual.

. Turn ignition from OFF to RUN 5 times within 10 seconds, with the 5th time ending
in RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle
to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will
cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

Mar 02, 2009 | 1996 Mercury Sable

1 Answer

I do not have the owners manual for the 2007 grand caravan


  1. clear channels by holding the 1 & 3 buttons down for 10 secs.
  2. to program hold remote no more than 3" from console,press and hold remote button and button you want to program the message center will say channel training then channel trained release w/you see channel trained
  3. you may have to push train button on garage door opener and repeat step 2
  4. use step 3 only after 1&2 fail.

Nov 16, 2008 | 2007 Dodge Caravan SXT Minivan New Cars

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...