Question about Cars & Trucks

Open Question

What is the timing marks on a diesel c240 4ab1 engine for injection pump timing

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22156 Answers

SOURCE: need the timing marks for a 3.1 td 5 cyl diesel injection pump

isusu engine?? have you looked for a 8mm hole in timing gear that corresponds with a hole on plate behind then lock it in with a bolt ,remove bolt after tightening belt .DONT FORGET THIS ???.....if you cant find anything do it with no timing marks easy --- piston no 1 at tdc valves closed spin pump till fuel comes out of no 1 injector feed and lock it all together,indirect diesel is 6/8 ,,,,,direct injection is 12/16,,,,and turbo is 18/22 btdc

Posted on Dec 13, 2008

  • 4 Answers

SOURCE: HELP!!!!need timing marks for pajero 94 2.8 auto *** import

there is a little mark on the crankshaft which you line up with the 'o' mark on the casing ..
remove the cam cover and look at the cam you should see a nob on the cam about 3 th lob and that should be facing just left of the engine ..
if you have a turbo there is two notchs on the injection pump pully ..if turbo there is a 't' mark on the rear of the cover the notch on the pully should mark up with the 't'..
the timing is set..

Posted on Mar 09, 2009

The GQ
  • 32 Answers

SOURCE: chevrolet 2.8 litre diesel fuel pump to engine timing

They have 2.8 liter diesels???

Posted on Sep 20, 2009

  • 1 Answer

SOURCE: S4S diesel engine cant start it up had fuel pump done

How to set the injector pump timming?

Posted on Apr 22, 2010

  • 153 Answers

SOURCE: where can i find timing

Hi, no marks as such, but with the crank marks lined up to TDC No/1 if you look at the cam pulley and the pump pulley you should see a hole in both at about 2o'clock position, these holes should line up with corresponding holes of which you screw a bolt in each ( I think they are 8mm metric ) by doing this the bolts hold both pulleys in the correct position with crank marks aligned, cheers hope that helps

Posted on Oct 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok, what degree before tdc is the spill timing on No one piston?


if you are talking inline fuel pump for a diesel engine ( only unit that allows for spill timing) you set the injection mark on the pointer and spill shut off is at that mark
with diesels there are a number of differences as to the different makes of engines as some are 15 degrees up to 22 degrees but they are all set on the INJ mark
talk with a specialist diesel shop as to the degrees for your make of engine as it is critical to prevent engine damage

Jul 07, 2016 | Cars & Trucks

2 Answers

How do I set injection pump timing


you haven't given which make , model,year of engine type of fuel pump, make of fuel pump and the only clue is the flywheel
the injection timing mark is normally denoted as a lightning symbol and you will find it anywhere between 14 degrees btdc to 22 degrees btdc
or it will be set at the degrees btdc r recommended by the manufacturer
It has to be exact because after that mark will be down on power and too far advanced will melt pistons

May 19, 2016 | Cars & Trucks

1 Answer

A Isuzu NPR 4hf1 rotary pump timing marks set


Hi. If it has a rotary pump, the pump needs to be installed with the crank at 49 deg BTDC on the compression stroke cyl 1. Mark dot gear on pump with white paint. Line up dot gear on pump with line on pump bracket and install. Remove PRM sensor from bell housing and check if line on pump gear is still lined up with line on pump bracket.

Feb 05, 2015 | Isuzu Cars & Trucks

1 Answer

Ford ranger 2.5 diesel pump timing marks


Could you give me injection pump gear pump timing for a Ford renger 2.5 diesel 2007 please

Apr 29, 2012 | Cars & Trucks

1 Answer

I need to know where the timing marks are on a 96 4wd isuzu rodeo. CAN ANYBODY HELP ME PLEASE?



  • I hope you get this, I was going to go to bed until I noticed how bad you were needing some timing marks :)

  • Injection pump and camshaft alignment marks-diesel engine
ironfist109_302.jpg

ironfist109_303.jpg

  • Tensioner pulley bolt sequence (diesel)


ironfist109_304.jpg


  • Crankshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_305.jpg

  • Camshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_306.jpg
  • Timing belt installation sequence-2.3L and 2.6L engines
ironfist109_307.jpg
  • Timing belt tensioner lockbolt-2.3L and 2.6L engines
ironfist109_308.jpg

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 06, 2011 | 1996 Isuzu Rodeo

1 Answer

Timing marks trooper 1985 mod dlx turbo diesel


Refer to Figures 1,2,3,4 when performing 17-step timing procedure for 1981-1985 Diesel Engines.

Fig 1. Injection pump and camshaft alignment marks - Diesel engine.

archaeology_66.jpg


Fig 2. Removing the timing belt holder - Diesel engine.

archaeology_67.jpg

Fig 3. Injection pump alignment marks - Diesel engine.

archaeology_68.jpg

Fig 4. Tensioiner Pulley Bolt Sequence - Diesel engine.

archaeology_69.jpg

Procedure - Timing Belt replacement.

1. Disconnect the negative battery cable. Drain the cooling system.

CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

2. Remove the timing belt cover. Remove the injection pump sprocket flange.

3. Using a prybar, remove the tension spring from the timing belt tensioner.

When removing the tension spring, avoid using excessive force for the spring may become distorted.

4. Remove the tensioner pulley bolt and the pulley.

5. Remove the timing belt and discard it.

To install:

6. Rotate the crankshaft to bring the No. 1 piston to TDC of the compression stroke.

7. Align the timing marks on the injection pump sprocket with the camshaft sprocket; the marks must be facing each other.

8. Using a new timing belt, install it in the following sequence: crankshaft sprocket, camshaft sprocket and the injection pump sprocket; the slack must be between the injection pump and camshaft sprockets.

9. Install the tension center and the tension pulley so the end of the tension center is fitted against both pins on the timing pulley housing.

10. Hand tighten the nut so the tension pulley can be rotated freely.

11. Install the tension spring and semi-tighten the pulley nut to 22-36 ft. lbs. (30-48 Nm).

12. Rotate the crankshaft 2 full turns clockwise to seat the belt and further turn the crankshaft 90° beyond TDC to settle the injection pump.

13. Loosen the tension pulley nut to take up the timing belt slack. Tighten the tension pulley nut to 79-94 ft. lbs. (108-128 Nm).

14. Install the injection pump sprocket flange; the hole in the outer circumference of the flange should be aligned with the triangular timing mark on the injection pump sprocket.

15. Rotate the crankshaft 2 full turns clockwise to bring the No. 1 piston to TDC of the compression stroke. Make sure the triangular timing mark on the timing sprocket is aligned with the hole in the flange, then, measure the timing belt tension; it should be 33-55 lbs.

16. Install the timing belt cover.

17. Connect the negative battery cable.

Jul 04, 2011 | 1995 Isuzu Trooper

1 Answer

Need the timing marks for a 3.1 td 5 cyl diesel injection pump


isusu engine?? have you looked for a 8mm hole in timing gear that corresponds with a hole on plate behind then lock it in with a bolt ,remove bolt after tightening belt .DONT FORGET THIS ???.....if you cant find anything do it with no timing marks easy --- piston no 1 at tdc valves closed spin pump till fuel comes out of no 1 injector feed and lock it all together,indirect diesel is 6/8 ,,,,,direct injection is 12/16,,,,and turbo is 18/22 btdc

Dec 13, 2008 | 2001 Jeep Grand Cherokee

1 Answer

Timing diesel fuel pump


hi
first remove the timing cover afer remove also remove the crankshaft pully.
now you can see timing belt clearly next remove the valve cover to see valves.
Rotate the engine by hand you can see where you remove the engine bully key grove that key should be top side while you rotating the engine there is mark like -- on the cover behand where you remove the pully so that mark and the crank shark key should in lined.
after that look the injection pump pully you can see front side mark --- look the engine direct behand the bully you can see mark that two mark should be in line have look the engine valves first cylinder should be close and the 4cylinser exhaust valve open.
i thing that will help you.

dont worry this language is my second language.if i make any mistake how i typing.

Jul 02, 2008 | 1985 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...