Question about Chrysler Cars & Trucks

Open Question

2005 chrysler pacifica will not stay runnning after motor and transmission replaced

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75117 Answers

SOURCE: Set clock

Beside the analog clock display there is a small dot where you can insert a pen. When you push this in gently the clock starts moving very fast. Hold this button in until the time is correct. Make sure you stop before you go by the time you want because it only goes in one direction

Posted on Dec 18, 2008

MrScary66613
  • 1990 Answers

SOURCE: I need to replace the thermostat for a 2005 chrysler pacifica

Follow the Upper Radiator Hose to the Block. There is a Bell housing there that the Hose Connects to. Remove that Bellhousing and the Thermostat is Right Under it.

Posted on Jan 15, 2009

hotrodtod38
  • 141 Answers

SOURCE: Brake fluid reservoir on a 2005 Chrysler Pacifica

WHEN YOU OPEN YOUR HOOD LOOK DOWN THE DRIVER SIDE FENDER THEN LOOK LEFT ABOUT 10 INCHS AND YOU SOULD FIND IT IT WILL BE WHITE IN THE ENGINE COMPARTMANT AREA

Posted on Feb 14, 2009

  • 4 Answers

SOURCE: 2006 Chrysler Pacifica Auotmatic Liftgate

Yes new gas shocks on the lift gate will fix your problem. I had the same problem on my 2005 Pacifica and when it hit my head- I came up with the solution.

Good Luck,
Ray

Posted on May 11, 2009

turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Chrysler Pacifica. It is making a grinding noise, and won't drive,reverse or stay in park. It was shifting gears perfectly before everything stopped working. Any idea?


Check the CV axles first. They can pop out and cause your noise and won't keep the vehicle from moving in park. Replace the axle/s if they did.

Sep 22, 2016 | 2005 Chrysler Pacifica

1 Answer

How do I change egr valve on a 2005 chrysler pacifica ?


If car does not stay runnin or stalls wen slowin down is egr effects. It may be the gasket wher it connects to engine. Sonetimes u can blow out carbon in the valve itself. Seek a shopmanual at local library

Jul 27, 2015 | 2005 Chrysler Pacifica

1 Answer

Ac/ heater f motor speeds up and slows down while runnning, what could be the issue


Check voltage to the fan blower motor. If its within limits, the blower motor is most likely bad.

Jul 08, 2014 | 2005 Chrysler Pacifica

1 Answer

2005 chrysler pacifica I don't know what else to say. I brought this car about two years ago and I have replace engine and transmission mounts twice, yet again I am told I need to replace mounts. I have...


And no one has the steps on how to replace this yourself. Its a pain and Chrysler will not warranty or re-call these cheap mounts. Ill be getting rid of my Pacifica soon.

Aug 27, 2010 | Chrysler Pacifica Cars & Trucks

3 Answers

2005 pacifica p0700 touble code problem


The P0700 refers to a Transmission Control System Malfunction. It's a generic code in that it's a warning to have your transmission computer scanned to get the precise codes in order to diagnose the problem further. Apparently, transmission issues are common in all Chrysler products in the mid 2000's . Have the car scanned for a more specific code and post back your results for further instruction.

Oct 28, 2009 | 2005 Chrysler Pacifica

1 Answer

2006 Chrysler Pacifica Auotmatic Liftgate


Yes new gas shocks on the lift gate will fix your problem. I had the same problem on my 2005 Pacifica and when it hit my head- I came up with the solution.

Good Luck,
Ray

Apr 25, 2009 | 2005 Chrysler Pacifica

1 Answer

The LED light is out for the climate control on the AC.


i have seen this before and what i found to be the problem was the blower motor resistor block shorted out and kept the motor power up all the time. and would end up killing the battery. the resistor is located on the passenger side under the dash kinda behind the glove box

Jan 03, 2009 | 2005 Chrysler Pacifica

1 Answer

2005 Chrysler Pacifica Seat motor replacement


it the recline motor , motor 75.00 it not hard to do

Oct 06, 2008 | 2005 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...