Question about Cars & Trucks

Open Question

Why does my cress kiln stop clicking around temperature 1400 and start again around 1700

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

spiescic
  • 38 Answers

SOURCE: The set code button on my Cress E27 kiln quit working

Could you let me know if its the stock Cress controller or other controller. I have the schematics to a Skutt controller. They operate some what the same. Knowing the voltage and phase of your electrical supply connection would tell me what to send you.

Stevan
spiescic@cogeco.ca

Posted on Mar 09, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need an owners manual for modet lt-3k kiln


Do you mean the Dawson LT-3K kiln sitter, a control and monitor for the ceramic kiln? The manual for this is on the product page: http://www.paragonweb.com/ManualInfo.cfm?CID=42 . The direct link to the manual is http://www.paragonweb.com/files/manuals/ACF1B.pdf .

If you need information about the kiln, then please check that model number and add a comment with that information. If your kiln is from Paragon, then try http://www.paragonweb.com/Instruction_Manuals.cfm for a manual. Paragon makes the Dawson LT-3K.

I hope this helps.

Cindy Wells

Mar 26, 2017 | Cars & Trucks

1 Answer

Hi My 2005 Same Dorado 85 Tractor. It starts from cold easily first time around. But once the engine has been running for several minutes it stops.


sounds like you could have a coolant temp sensor issue. If it senses the engine temperature higher than it actually is, it will tell the engine computer to shut down.

Also I'm not showing an 05 Eldorado, if you could give the correct information for your car, it would be very helpful

Feb 15, 2017 | Cars & Trucks

2 Answers

18 wheelers what rpms do I start shifting from 1st to 2nd when hauling 80,000 lbs with a Detroit engine and 13 speed tranmission


1st 1000 rpm
2nd 1300 rpm
3rd 1400 rpm
4th 1500
5th 1600
6th 1700
7th 1700
8th 1700
etc

Oct 14, 2015 | Cars & Trucks

1 Answer

The set Code button on my Cress E27 kiln quit working, so I need a wiring diagram to determine if q wire is disconnected or corroded


Could you let me know if its the stock Cress controller or other controller. I have the schematics to a Skutt controller. They operate some what the same. Knowing the voltage and phase of your electrical supply connection would tell me what to send you.

Stevan
spiescic@cogeco.ca

Mar 09, 2014 | Cars & Trucks

1 Answer

Hi my vauxhall combo 1700 di 54 plate wont start


I'D REPLACE THOSE SENSORS OR REPAIR THE WIRING WHICH EVER IS THE CAUSE. YOU NEED A LIVE DATA SCANNER TO DO THIS REPAIR MOST LIKELY. THAT MEANS THE DEALER.

Oct 05, 2012 | Vauxhall Cars & Trucks

1 Answer

Where is the crankshaft position/crank angle sensor located on a 2005 kia sedona


Hi, at the front of the crankshaft. if its near time for the timing belt, you want to replace it along with any pullies, tensioner and water pump


The crankshaft position sensor is mounted on the engine near the crankshaft.

Operation

The crankshaft position sensor is a Hall-Effect sensor that senses the crank angle (piston position) of each cylinder and converts it into a pulse signal. The signal from the sensor is relayed to the ECM to indicate engine rpm and the position of the crankshaft.

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor in place.
  4. Remove the sensor from its mounting. To install:
    1. Installation is the reverse of the removal procedure.
    2. Clearance between the sensor and the sensor wheel should be 0.020-0.059 inch. 2002-2005
      1. Properly connect the scan tool.
      2. Start the engine and allow it to idle.
      3. Be sure the idle position switch is ON.
      4. Specifications are as follows:

        Temperature - 4°F, test specification 1500-1700 RPM Temperature 32°F, test specification 1350-1550 RPM Temperature 68°F, test specification 1200-1400 RPMTemperature 104°F, test specification 1000-1200 RPM Temperature 176°F, test specification 650-850 RPM

Mar 16, 2011 | 2003 Kia Sedona

2 Answers

2001 325i engine vibration around 1700 to 2000 rpms


could be new engine mounts or miss fire ...

Jan 04, 2010 | 2001 BMW 325

1 Answer

Car stalls when you come to a stop when car gets hot


i would have your idle air control solenoid replaced and also check for vacuum leaks.thank for the question

Jan 30, 2009 | 2003 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...