Question about Nissan Cars & Trucks

Open Question

ECM 0087 my nissan frontier show check engine indicator...pls help me

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Pattods
  • 116 Answers

SOURCE: 1998 nissan frontier 4x4

Well since the lights are controlled by the OBD (on board diagnostics), you'll have to reset it. You may be able to do this by simply disconnecting the battery for a few hours. However, a lot of newer vehicles have electronically locked radios which require the manual to be able to be re-enabled.

I'd check out the radio before disconnecting the battery.

The only other ways are to physically disconnect the lights in the dash or get someone with an OBD reader to clear the codes.

Posted on Sep 13, 2008

TwinTurboZ
  • 78 Answers

SOURCE: 2000 Nissan Xterra Service Engine soon indicator is always on

The knock sensor is not a huge deal to replace and will not turn on the light. It should be dont though.

The crankshaft sensor is located directly between the engine and transmission. It is dead center at the bottom.

Posted on May 21, 2009

Murphybanton
  • 2004 Answers

SOURCE: nissan frontier 98

Visit http://www.troublecodes.net/Nissan/95ams96-00.shtml#frontierx24

for code listing for your car.

Rate this.

Posted on Aug 09, 2009

  • 3640 Answers

SOURCE: engine repair code P0325

po325--ignition system or missfire.

Posted on Sep 16, 2009

  • 7353 Answers

SOURCE: No power to cigarette lighter. have checked and

there are 3 fuses that operate that. #42 (15 amp) power socket, #18 (10 amp) power socket relay (power socket only operates with key on) and #23 (15 amp ) Cig lighter, key on.... have you checked all 3 fuses??

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does the temperature gauge reads hot when switch is turn on Nissan frontier 98


If your temperature gauge reads hot as soon as you turn the ignition on it's probably due to a faulty temperature sender. The link below may show you the location of that sensor:

nissan frontier temperature sender Google Search

The sensor is very easy to change. It just screws into the block. It may have a 'brass' appearance and have either 1 or 2 electrical wires attached.

To change it, simply disconnect the wire and then use a wrench to unscrew it.

Feb 21, 2016 | Nissan Cars & Trucks

1 Answer

How do i reset a 2001 nissan frontier anti theft?


check / replace the battery in the fob key
use a scan tool to reset the ECM
Have this done by a service center conversant with nissan products as there is a special procedure to get the ECM to respond

Dec 20, 2015 | 2001 Nissan Frontier

1 Answer

My nissan frontier 2005 light came on it says this code [ po305] cylinder 5 misfire. The 5th spark plug is not working. I have checked the compression, ignition coil, pressures, pistons, current and I


You will need a wiring diagram for this, but find the wires that run your cylinder 5 coil. trace it back to the ecm and see if you are getting voltage from the ecm.

Sep 29, 2014 | 2005 Nissan Frontier

1 Answer

2002 Nissan Frontier showing a P01444 code


P1444 EVAP Canister Purge Volume Control Solenoid Valve
This system controls flow rate of fuel vapor from the EVAP canister. The opening of the vapor by-pass passage in the EVAP canister purge volume control solenoid valve changes to control the flow rate. The EVAP canister purge volume control solenoid valve repeats ON/OFF operation according to the signal sent from the ECM. The opening of the valve varies for optimum engine control. The optimum value stored in the ECM is determined by considering various engine conditions. When the engine is operating, the flow rate of fuel vapor from the EVAP canister is regulated as the air flow changes.

Feb 11, 2014 | Nissan Frontier Cars & Trucks

1 Answer

I have a 2002 Nissan frontier SC, 69000 miles. Motor runs well when first start the engine and runs very routh after warm up and it just stops sudenly the engine. Three codes P0328(knock sensor 1 circ


P0328 Is knock sensor code,all Nissan have this code so leave,concentrate on P0101 and P0103 this is MAF(mass airflow),Just make sure the timing belt is in good condition and the marks are correct, your solution is NTB02-003A In other word you need a reprogram on the ECM

Mar 19, 2012 | 2000 Nissan Frontier

1 Answer

Where is the ECM relay located on a 2005 frontier? I heard thier maybe a problem associated with this component.


Hello tdyre13
The ECM relay is located in the power distribution ctr. under the hood at the right rear of the engine
compartment. Hope this helps.

Jan 24, 2011 | 2005 Nissan Frontier

1 Answer

2000 nissan frontier knock sensor code & distributor


no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Jun 14, 2010 | 2000 Nissan Frontier

3 Answers

2005 frintier crew cab hesitate


Sounds like your ECM relay. They are one recall on some 2005 Frontier trucks.

Mar 23, 2009 | 2005 Nissan Frontier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...