Question about Mercury Cars & Trucks

Open Question

Location of crankshaft position sensor on 1991 Mercury Topaz

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: Crankshaft position sensor location - 1991 Dodge Dakota 5.2L

it is on the passenger side on the back off the motor.there are two allen head bolts or 13mm.it goes into the transmission and normally has rubber at the opening.you should be able to gets this from the top follow middle of valve cover on pass. side the go strait back toward the fire wall.please rate this answer.

Posted on Jan 30, 2009

Ad
emissionwiz
  • 77169 Answers

SOURCE: crankshaft position sensor location for a 98 lincoln towncar

it is on the front of the engine down low, here is a picture.
bfdacb9.jpg

Posted on May 11, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

Posted on Apr 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Location of crank sensor 05 mercury montego


Ford/Mercury are usually located by the harmonic balancer.

May 01, 2016 | Mercury Cars & Trucks

1 Answer

Crank position sensor


This sensor should be on either side of the crankshaft pulley. It would be protruding across the surface of the crankshaft pulley. You can go to an autoparts site and look at photos of the part.

Jan 19, 2014 | 1993 Mercury Topaz

1 Answer

May i see the location of the crankshaft position sensor on '93 sable 3.0L


For the 3.0 Vulcan 12 valve engine, it's on the front of the engine, just up to the left of the crankshaft pulley. One illustration indicates about the 11:00 o'clock position relative to the pulley, and may be obscured by waterpump

9_11_2012_8_45_37_pm.jpg

Sep 11, 2012 | 1993 Mercury Sable

1 Answer

1991 Mercury Topaz engine stalls while driving...replaced temp sensor regarding pumping fuel...but that didn't solve problem. Any ideas?


Hey check out my thread, see if we are having the same problem, sounds familiar possibly.

http://www.fixya.com/ThreadAsker.aspx?thid=7662591

Jan 14, 2011 | 1991 Mercury Topaz 4 Door

1 Answer

Looking for location of crankshaft position sensor on 2000 mercury villager with 3.3l engine. parts store says there are 2 per vehicle. found one at front of engine. any idea where the 2nd one would be?


The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing The bottom of the sensor is positioned next to the drive plate. Remove the 10mm bolt holding the sensor in place and remove the sensor. Install the new crankshaft sensor.
Install crankshaft sensor bolt and tighten. Connect wiring. merry christmas !!

Dec 25, 2010 | 2000 Mercury Villager

1 Answer

1991 Mercury Topaz


I'm surprised there isn't a cover that has the diagram on it but for the fan its gotta be a relay under the hood i'd say

Apr 05, 2010 | 1991 Mercury Topaz 4 Door

1 Answer

Location of cam positioning sensor for 1991 chev lumina 3.1


On your 1992 Chevrolet Lumina-Sedan/Coupe 3.1L MFI OHV , the Crankshaft Position Sensor is located: clearpixel.gif Under hood, passenger side, lower engine area, passenger side of engine block, mounted front of crankshaft pulley

Nov 30, 2008 | 1992 Chevrolet Lumina

2 Answers

Doesn't want to run after outside temp reaches about 60 degrees


i think something is chokeing it either the air filter or the catalytic converter or it could be 1 of the intake sensors

Nov 17, 2008 | 1991 Mercury Topaz 4 Door

1 Answer

My mercary topaz will only ideal at 3000 rpms, what part do I need to replace??


It sounds like the throttle position senor could be bad. Terry

Jul 20, 2008 | 1991 Mercury Topaz 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

fordexpert

Level 3 Expert

5572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...