Question about Mercury Cars & Trucks

Open Question

Location of crankshaft position sensor for 1991 Mercury Sable

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: Crankshaft position sensor location - 1991 Dodge Dakota 5.2L

it is on the passenger side on the back off the motor.there are two allen head bolts or 13mm.it goes into the transmission and normally has rubber at the opening.you should be able to gets this from the top follow middle of valve cover on pass. side the go strait back toward the fire wall.please rate this answer.

Posted on Jan 30, 2009

  • 599 Answers

SOURCE: Crankshaft Position Sensor

the dual crankshaft position sensor is secured in an aluminum mounting bracket and bolted to the left side of the timing chain cover, partially behind the crankshaft balancer, hope this helps get back to me if you need mre help. please rate my fix as i strive to be the best

Posted on Apr 29, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

roniecon
  • 6826 Answers

SOURCE: were is the crankshaft position sensor located on 2001 chevy mali

It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Posted on Mar 22, 2010

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

Posted on Apr 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Location of crank sensor 05 mercury montego


Ford/Mercury are usually located by the harmonic balancer.

May 01, 2016 | Mercury Cars & Trucks

1 Answer

Were is the crankshaft position sensor located on 95 ford 3.0 sable


See the attached image. It may not be exact but should get you in the ballpark.
25282268-cqcheelhvatlzkmvt50ynpkc-1-0.jpg

Nov 13, 2014 | 1995 Mercury Sable

1 Answer

1998 Mercury Sable: car will not start, cranks over but no spark from spark plug wire. Is there a fuse or is there something not hooked up? Do I need a new coil?


If you have no spark, I would test the crankshaft position sensor. If it's not that then probably the coil pack. Without a crankshaft sensor signal, you will get no spark. Same goes for the coil pack. I would bet on the crankshaft position sensor being bad. Good luck.

Aug 27, 2013 | 1998 Mercury Sable

1 Answer

May i see the location of the crankshaft position sensor on '93 sable 3.0L


For the 3.0 Vulcan 12 valve engine, it's on the front of the engine, just up to the left of the crankshaft pulley. One illustration indicates about the 11:00 o'clock position relative to the pulley, and may be obscured by waterpump

9_11_2012_8_45_37_pm.jpg

Sep 11, 2012 | 1993 Mercury Sable

1 Answer

Where is the ckp sensor on a 2002 Mercury Sable LS 3.0 24V DOHC V6? I have slight missfire.


Its located by the harmonic balancer. Here's the info on how to replace it. Crankshaft Position (CKP) Sensor - 3.0L (4V) Removal and Installation
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the accessory drive belt. For additional information, refer to Section 303-05.
  1. Remove the nut and position the power steering pressure tube muffler and bracket assembly out of the way.
    a0075632.gif
  1. Remove the RH inner fender splash shield
    • Remove the screws and the pin-type retainers.
    • Remove the splash shield.
    a0010439.gif
  1. Remove the screws and the generator splash shield.
    a0039750.gif
  1. Remove the LH upper stud and the lower retaining bolt. Loosen the RH upper retaining stud.
    a0077407.gif
  1. Pivot the generator away from the engine block.
    a0079945.gif
  1. Remove the support bracket.
    1. Remove the nuts.
    1. Remove the bolts.
    1. Remove the bracket.
    a0079767.gif
  1. Remove the crankshaft position (CKP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt and the CKP sensor.
    a0006825.gif
  1. To install, reverse the removal procedure.

Mar 06, 2011 | 2002 Mercury Sable

2 Answers

Where is the crankshaft positioning sensor on a 2001 mercury sable


on the engine block by the pulley:

f051b5a.gif
It is the plug-looking part with the wires.

The Crankshaft Position (CKP) sensor is a variable reluctance sensor that uses a trigger wheel to induce voltage. The CKP sensor is a fixed magnetic sensor mounted to the engine block and monitors the trigger or "pulse" wheel which is attached to the crank pulley/damper.

Oct 31, 2009 | 2001 Mercury Sable

1 Answer

Need to know what fires coil 1995 mercury sable both wires to coil have power when key is turned on car cranks no spark from coil new coil what gives the coil extra power to fire


what engine? 3.0L 2 Valve? 4 Valve?
3.4L SHO engine?

The PCM (engine computer) fires the coils, but it is never the cause of a problem. I suspect it is the crankshaft position sensor on the front of the engine by the crank pulley. easy to change.

Crankshaft Position Sensor The crankshaft position sensor (CKP sensor) (6C315) is a variable reluctance sensor triggered by a 36-minus-1 tooth trigger wheel located on the crankshaft pulley and damper. The signal generated from the crankshaft position sensor is called the crankshaft position (CKP) signal, which provides base timing and crankshaft speed (rpm) information to the ignition control module (ICM) (12K072). Base timing is set at 10±2 degrees before top dead center (BTDC) AND IS NOT ADJUSTABLE. The powertrain control module (PCM) (12A650) will use this information with the spark advance information to determine ignition coil (12029) turn on or turn off time.

Sep 15, 2009 | 1995 Mercury Sable

1 Answer

Location of the camshaft position sensor in a 2004 mercury sable


it is located on top of the engine right below the air inlet tube at the base of the intake it is a black sensor on top of a silver housing where the distributor would normally be

May 01, 2009 | Mercury Sable Cars & Trucks

1 Answer

Just need information


one it is near catalyst converter in the front under engine.

Feb 07, 2009 | 1991 Mercury Sable

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...