Question about 2005 Chevrolet Colorado

1 Answer

My wipers will not come on i have replace the maine switch and allrealys all fuses are ok what know to check 2005 colorado 3.5

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Chevrolet Master
  • 224 Answers

Power up the motor directly from the battery Larry...to see if its operational.

Posted on Apr 27, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005. Why doesn't windshield wiper stop?


There's a switch on the motor; when you turn it off, it's going to continue till the wipers are in the "park" position. Possibly a ca or internal cam or detent activates a switch to stop rotating. You might need a new wiper motor if the position switch isn't external.

Oct 18, 2015 | Ford Ranger Cars & Trucks

1 Answer

My wipers just quit working, fuses ok....any thoughts?


Dead wiper motor. Or very bad wire connection. Or possibly bad relay after fuse, and before wiper motor. You can test motor by a direct jumper from positive to the motor's positive terminal.

Apr 10, 2015 | 2005 Chevrolet Colorado Extended

1 Answer

Fuse number for winderwiper


Hi Maddie, I'm glad to help! Below, I have posted a diagnostic procedure to see why the wipers are not working on your Dakota. Hope this helps and have an awesome day Maddie!



DIAGNOSIS
WIPER MOTOR

The following are wiper motor system problems,
tests to be performed to locate the faulty part, and
the proper action to be taken. If the malfunction involves
only the delay mode, switch, or wiring, see the
diagnosis for Intermittent Wipe Module and Wiper/
Washer Switch.
CONDITION
Motor will not run in any wiper/washer
switch position.
PROCEDURE

(1) Check fuse 10 in the fuseblock module. If OK,
go to step 3. If not OK, replace fuse and go to next
step.
(2) Check motor operation in all wiper/washer
switch positions. If not OK and fuse blows, go to step
5. If not OK and fuse is OK, go to next step.
(3) Place wiper/washer switch in LOW position and
listen to motor. If you cannot hear it running, go to
next step. If motor is running, check motor output
shaft. If output shaft is not turning, replace motor
assembly. If it is turning, drive link to output shaft
or linkage is not properly connected. Replace worn
parts and/or properly connect drive link to the motor
output shaft.
(4) Connect a voltmeter between motor terminal L
and ground strap (Fig. 1). If there is little or no voltage
(less than 1 volt), move negative test lead from
the ground strap to battery negative terminal. If an
increase in voltage is noticed, the problem is a bad
ground circuit. Make sure the motor mounting is free
of paint and that mounting fasteners are tight. If
there is still no indication of voltage, the problem is
an open in wiring or faulty wiper/washer switch. If a
small increase (greater than 3 volts) in voltage is observed,
the problem is a faulty motor assembly.
(5) Disconnect motor wiring connector and replace
fuse. If fuse does not blow, motor is defective. If fuse
blows, wiper/washer switch or wiring is at fault.
CONDITION
Motor runs slowly at all speeds.
PROCEDURE

(1) Disconnect wiring harness connector at motor.
Remove wiper arms and blades. Connect an ammeter
between battery and terminal L on motor (Fig. 2). If
motor runs and average ammeter reading is more
than 6 amps, continue to next step. If motor runs
and average ammeter reading is less than 6 amps, go
to step 3.
(2) Check wiper linkage or pivots for binding or obstruction.
Disconnect drive link from motor. If motor
now runs and draws less than 3 amps, repair linkage
system. If motor continues to draw more than 3
amps, replace motor assembly.
(3) Check motor wiring harness for short between
high and low speed circuits. Connect a voltmeter or
test lamp to motor ground strap. Set wiper/washer
switch to LOW position. Connect other lead of voltmeter
(test lamp) to terminal H of the wiring harness.
If voltage is present, there is a short in the
wiring or wiper/washer switch. If no voltage is
present, go to next step.
(4) Set wiper/washer switch to HIGH position.
Move voltmeter (test lamp) lead from terminal H to
terminal L of the wiring harness. If voltage is
present, there is a short in the wiring or wiper/
washer switch.
CONDITION
Motor will run at high speed, but not at low
speed.
Fig. 1 Voltmeter Between Terminal L and Ground

Motor will run at low speed, but not at high speed.
Fig. 2 Ammeter Between Terminal L and Battery
WIPER AND WASHER SYSTEMS 8K - 3

Apr 26, 2014 | 1995 Dodge Dakota

1 Answer

My 2005 chevy colorado wipers quit working and keeps blowing fuses to the brake lights


check for bare wires associated with the wipers..u might have a simple short out problem

Jun 09, 2010 | 2005 Chevrolet Colorado

1 Answer

Neon wiper trouble


https://s24.postimg.org/g7k0yez1x/wiper.jpg

Click on the link
See the fuse, key on, use a test lite and check for voltage at fuse circuit, it should be hot.
See pins 4 and 5 at wiper motor, those wire colors should be voltage for hi and/or lo speed, use the test lite, check for voltage hi and or low speed on those wire colors.
At the moment, I think your wiper/washer switch is faulty?

Jul 09, 2017 | 2005 Dodge Neon

1 Answer

My colorado break lights aren't working I checked the fuse and the balbs and they all look good. What should I check next


break light switch mounted under the break pedal or on the main break cylinder.If you shortcut the wire on the switch the break lights should light up.

Jul 15, 2009 | 2005 Chevrolet Colorado

2 Answers

2005 Taurus. Winshield washer not working.


This may be multi-function switch failure. The multi-function is the turn signal/wiper/headlight switch. It may need to be replaced. Is this the type of switch you have. Hope this helps. If it is not the switch then the pump may be bad or have a bad wire connection.
GOOD LUCK

Jan 16, 2009 | 2005 Ford Taurus

1 Answer

Wiper motor problem


Check the Relay in the Battery Junction box it is the 3rd one from edn oposite if 3 small fuses close to it with a 5 amr fuse in the middle. Hope this helps it realy should from the sounds of it

PLEASE RATE My ANSWER

Dec 27, 2008 | 2005 Ford Taurus

1 Answer

BMW 740IL Wiper Issue


try checking for a short to power on ur 12 volt comming into motor also check for a good ground at the plug for ur wiper motor

Jun 16, 2008 | BMW 750 Cars & Trucks

Not finding what you are looking for?
2005 Chevrolet Colorado Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...