Question about Ford F-250

Open Question

Location off the clutch starter switch on 1988 f250

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 1994 Tercel Clutch ignition switch

the switch is located next to the peddle, what you can do is to connect the cables and eliminate the switch.

Posted on Jul 16, 2008

Ad
  • 314 Answers

SOURCE: starter

My friend, Please take this to a shop! They will change this in minutes! Frankster016

Posted on Oct 19, 2008

emissionwiz
  • 77169 Answers

SOURCE: locate fuel pump alternate switch and how to reset it.

the fuel pump cut off safety switch (inertia switch) is near the parkbrake pedal.there is a push button on top, push it to reset

Posted on Apr 10, 2009

wyatt1582
  • 453 Answers

SOURCE: How to get top bolt off of 1988 F250, 7.1 L diesel starter

You need a long extension and swivels for a rachet to get to the one bolt thats on top next to the block. Check for a way to get to it from the front.

Posted on Jun 26, 2009

  • 416 Answers

SOURCE: where is the clutch /starter interlock switch

clutch pedal

Posted on Jan 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starting Issues


Replace the starter solenoid on the fire wall. If you jump it and still no turning. replace the starter..

Dec 26, 2015 | 1988 Ford F 250

1 Answer

Wireing diagram for 1972 ford f250 starter safty switch & backup ;light switch


neutral safety switch is bad or miss aligned this switch is located at the bottom of the steering column unless it's a standard then it was connected to the clutch pedal or stick shift depending on tranny option being it is a truck the most common spot was at the bottom of the column

Sep 01, 2014 | Cars & Trucks

1 Answer

I have a 1988 2wd pickup and the starter won't


starter wont turn or engages the flext plate,flywheel and still wont turn engine over?if this is the case you have a seized up motor,but if it doesnt even click check signal wire from ignition switch for power when you turn the key to crank.if no power your ignition switch,park/neutral safety switch(clutch switch if manual trans) or wrongly installed wired could be the problem.

Jul 18, 2013 | Cars & Trucks

1 Answer

1988 honda prelude manual tranny,won't start,put in a new starter and still the stater will not turn on, check fuse,oil,battery, what else can i check?


Have you checked the neutral safety switch? The switch is designed to prevent the vehicle from starting unless the clutch is fully depressed. I am not quite sure where the switch is located, it may be under dash on clutch shaft or the transmission. Keep me posted on this matter.

Jun 29, 2010 | 1988 Honda Prelude

2 Answers

Need to locate where starter is in 1988 isuzu pick up truck , put new battery in today and will not crank when clutch is pressed in to start.


The starter is near the vicinity of the flywheel where the engine interfacing with the transmission. look from the bottom of the engine up you can spot it just like this image. fe4fc41.jpg

Dec 12, 2009 | 1988 Isuzu Pickup 2WD

1 Answer

I have a 89 f250 4x4 and I was pulling a trailer when the clutch pedal went right to the floor.Turns out the line had popped off and now the truck will not start,What holds the line in in the slave end and...


For starter,you must get the clutch line replace 1st.

You will need a friend to bleed the clutch slave cylinder.

Check your owner manual for the correct fluid.....most like be DOT3.

Your problem is cause be the electronic cut out. When you DO NOT press on the clutch it will disable the starter circuit.

IT IS A SAFETY THING.

It prevent someone for start the truck in gear.

Good luck

Jul 18, 2009 | 1988 Ford F 250

2 Answers

1988 Dodge Ram 150 318 V-8 Will not start. Battery good. Cables good.Starter is good. Put key in and Nothing. No clicks, nothing. Does this truck come with a spark igniter? Could this be the problem? Where...


Greetings!

Let's keep things simple to start with... Check the battery that it has sufficient charge. (I did say to keep it simple). Ensure the gear selector is in Park or Neutral if equipped with an automatic trans, or depress the clutch pedal if equipped with a manual trans.

Lastly, in keeping things simple... check all the fuses and fuse links (special fusible wire) that power is available to your vehicle's electrical system.

With a test light, check the starter relay with the key in start position is energising the starter relay... bypass the starter relay if no power is present. if the starter operates, you now know the problem is located within the start control circuit (from the key switch through the starter relay to ground via a neutral safety switch (auto) or clutch switch (Manual).

finding the fault should be quick with a circuit diagram.

Cheers, Jay

Apr 16, 2009 | 1988 Dodge Ram 50

1 Answer

Locate fuel pump alternate switch and how to reset it.


the fuel pump cut off safety switch (inertia switch) is near the parkbrake pedal.there is a push button on top, push it to reset

Apr 07, 2009 | 1988 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...