Question about Cars & Trucks

Open Question

Can anybody send me a pdf of actual size an measurements of this tool-en-461051 camshaft holder set 2006 gm, so that I can make one from the exact measurements?

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 319 Answers

SOURCE: tool for 2006 brake calipers I need size

buy a set of the torque bits they come in sets of 4 or 5

Posted on Jun 14, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How can I set timing of a Ford focus if I can't see the marks on the camgear

take number 1spark plug out and put number one piston at top dead center of the chamber that's will be your timing make sure to mark the harmonic balance r

Feb 07, 2016 | Ford Cars & Trucks

3 Answers

Bypass pulley install for pontiac gtp 2000

You can also purchase a shorter belt designed for ?the same vehicle without A/C option.should be a belt diagram for both options under ?the hood. Hope that helps

May 28, 2015 | 2000 Pontiac Grand Prix GTP

1 Answer

I have a 2006 trailblazer that is running super rough at idle. Code P0014 keeps coming up and we have replaced almost every sensor possible

GM issued a bulletin in regards to this code being set. The 2006 Trailbazer was included in it. In some cases the engine has had to be replaced due to excessive crankshaft end play.

Here is the bulletin. I would suggest you contact GM. They are aware of this problem.
Good luck, & i hope this helps.

Subject:DTC P0014, P0017, and/or Belt Noise - Inspect Actuator Solenoid and Crank End Play - keywords bearing cam chirp damaged debris internal light metal P0106 phaser replacement run SES squeak thrust #PIP3693B - (04/04/2006)

Models:2005-2006 Buick Rainier 2005-2006 Chevrolet TrailBlazer 2005-2006 GMC Envoy 2005-2006 Saab 9-7x with 4.2L Engine (VIN S - RPO LL8)

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

On rare occasions, a rough idle may be encountered with a P0014 and/or P0017 DTC. Due to the rough idle, a P0106 DTC may be stored too. This concern may be due to debris in the camshaft actuator system, which may be caused by a missing camshaft actuator solenoid screen or a worn crankshaft thrust bearing. Typically, this is the result of a camshaft actuator solenoid concern. If this is due to a worn crankshaft thrust bearing, some customers may also comment on a drive belt noise.

If this concern is encountered, follow the SI diagnostics and repair as necessary. If the SI diagnostics do not isolate the cause of this concern, ensure that camshaft actuator solenoid screens 1, 2, and 3 are in place as shown below:

(1)Screen for Advance Pressure to Camshaft Actuator(2)Screen for Pressurized Oil from Oil Pump(3)Screen for ****** Pressure to Camshaft ActuatorIf any of these screens are missing, replace the camshaft actuator solenoid, change the engine oil and filter, and evaluate the concern.

If all these screens are present, measure the crankshaft end play to determine if it is within the specification of 0.0044" - 0.0153" (0.112 - 0.388 mm). Typically, if excessive crankshaft end play is causing this concern, it will be obviously out of specification by .050" or more. If crankshaft end play is within specification, replace the camshaft actuator solenoid.

If the crankshaft end play is obviously out of specification, inspect the engine block for damage due to contact with the crankshaft. If engine block damage is present, contact the PQC (Product Quality Center) at 1-866-654-7654 for engine replacement authorization.

If there is no engine block damage present, disassemble the engine and inspect the following components for damage due to thrust bearing debris in the engine oil: all bearings, all journals, all valvetrain components, all timing components, and the crankshaft

Then, estimate what it will cost to replace the oil pump, camshaft actuator solenoid, all damaged parts, and to completely disassemble the engine to thoroughly clean all of the cylinder head and engine block oil galleys with oil galley brushes and soapy water.

After the repair estimate is complete, estimate what it would cost to replace the engine and contact the PQC to review these estimates as outlined in 02-07-30-029F.

Important: On 2006 models with excessive crankshaft end play, please submit a field product report by following 02-00-89-002D.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.
© Copyright General Motors Corporation. All Rights Reserved

Aug 26, 2011 | 2006 Chevrolet Trailblazer Ext

1 Answer

Looking for a 2.2 ecotec timing chain diagram with pictures

Getting the timing chain back on these engines can be tricky and requires more than just a diagram to get right. Here is how the timing chain should be reinstalled. Keep in mind that this engine can cause damage to the valves if the timing chain has any problems while the engine is running so it may not be a bad idea to setup the timing system as follows and do a compression test to make sure that everything is in order there.
Install the crankshaft sprocket with timing mark at the 5 o'clock position. Lower the timing chain through the opening in the top of the cylinder head. Carefully ensure that the chain goes around both sides of the cylinder block bosses (See 1 & 2 in picture):

Install the intake camshaft sprocket with the INT diamond at the 2 o'clock position. Hand tighten a NEW intake camshaft sprocket bolt. Route the timing chain around the crankshaft sprocket with the matching colored link aligning with the timing mark. Route the timing chain around the intake camshaft sprocket with the uniquely colored link (1) aligning with the INT diamond:

Install the timing chain tensioner guide through the opening in the top of the cylinder head. Tighten the timing chain tensioner guide bolt to 10 N·m (89 lb in):

Install the exhaust camshaft sprocket with the timing chain matching colored link (3) at EXH triangle aligned at the 10 o'clock position:

Ensure the timing marks and the colored links (1,2,3) are correctly aligned:

Use a 24 mm wrench to rotate the camshaft slightly, until exhaust sprocket aligns with the camshaft. Hand tighten the NEW exhaust camshaft sprocket bolt:

Install the fixed timing chain guide. Tighten the fixed timing chain bolts to 10 N·m (89 lb in):

Apply sealant, GM P/N 12378521 (Canadian P/N 88901148) compound to thread and install the timing chain guide bolt access hole plug. Tighten the chain guide plug to 90 N·m (66 lb ft):

Install the timing chain upper guide. Tighten the timing chain upper guide bolts to 10 N·m (89 lb in):

Inspect the timing chain tensioner. If the timing chain tensioner, O-ring seal, or washer is damaged, replace the timing chain tensioner. Measure the timing chain tensioner assembly from end to end. A new tensioner should be supplied in the fully compressed non-active state. A tensioner in the compressed state will measure 72 mm (2.83 in) (a) from end to end. A tensioner in the active state will measure 85 mm (3.35 in) (a) from end to end.

****If the timing chain tensioner is not in the compressed state, perform the following steps. Remove the piston assembly from the body of the timing chain tensioner by pulling it out. Set the J 45027-2 (2) into a vise. Install the notch end of the piston assembly into the J 45027-2 (2). Using the J 45027-1 (1), turn the ratchet cylinder into the piston:

Inspect the bore of the tensioner body for dirt, debris, and damage. If any damage appears, replace the tensioner. Clean dirt or debris out with a lint free cloth. Install the compressed piston assembly back into the timing chain tensioner body until it stops at the bottom of the bore. Do not compress the piston assembly against the bottom of the bore. If the piston assembly is compressed against the bottom of the bore, it will activate the tensioner, which will then need to be reset again. At this point the tensioner should measure approximately 72 mm (2.83 in) (a) from end to end. If the tensioner does not read 72 mm (2.83 in) (a) from end to end repeat the steps required to return it to it's compressed state above.

Install the timing chain tensioner. Tighten the timing chain tensioner to 75 N·m (55 lb ft). Use a suitable tool with a rubber tip on the end. Feed the tool down through the camshaft drive chant to rest on the timing chain. Then give a sharp jolt diagonally downwards to release the tensioner:

Use a 24 mm wrench to hold the camshaft. Tighten the NEW camshaft bolts to 85 N·m (63 lb ft) plus 30 degrees:

May 25, 2011 | 2002 Pontiac Grand Am

1 Answer

Need 2000 Audi A8 4.2 engine timing belt marks

There are no alignment marks on the camshafts, you must use the camshaft holder tool T40005 in conjunction with the crankshaft holder tool 3242 to properly align the camshaft and crankshaft

CAUTION: Incorrect removal or installation of the timing belt can result in damage to internal engine components.

Nov 19, 2010 | 2000 Audi A8

2 Answers

2002 ford focus. need to know where timing marks are to set it.

there are no marks, special tools are needed when replacing the timing belt.

Sep 25, 2009 | 2002 Ford SVT Focus

1 Answer

Where is the camshaft position sensor on a 2006 isuzu i280

You probably need a camshaft position actuator solenoid. 12597025 is the gm part number and its on the passenger side of cylinder head at the front of engine. They gave trouble when they first came out with this engine on this gm built truck. See for a picture.

Jul 01, 2009 | 2006 Isuzu i-280

1 Answer

Automotive repair

As best I can tell, it is a flat area machined into the cams of a dual overhead cam GM V6 engine. These flat areas are used to align the (4) camshafts during timing belt installation. I found a link on the web which details timing procedures, with photos. There also appears to be special tools required for this procedure.

Nov 02, 2008 | 1993 Chevrolet Lumina

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14309 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides