Question about Cars & Trucks

Open Question

V240.20.6speed GWM cam belt timing marks - Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: timing marks

2993b98.gif
this is for 1.9

Posted on Aug 21, 2008

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

  • 23 Answers

SOURCE: timing marks 2002 sonata 4 cyl twin cam balance shaft marks

look for marks on the timeing gears there sould be a couple notches. then bring them center to center

Posted on Dec 24, 2008

stevenhurc
  • 450 Answers

SOURCE: Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin

these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

Posted on Jun 29, 2009

  • 1757 Answers

SOURCE: timing marks on twin overhead cams 2.4 and crank mark.

Click on the following direct, Free Link. It has several Diagrams including the Timing Belt + Marks for your 2004 Hyundai Sonata 2.4L DOHC In-Line 4-Cylinder Engine (located on the bottom half of the Page on the Link). There are additional Diagrams that will prove to be helpful while you are doing this...

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/sonata/2004_hyundai_sonata_timing_belt_diagram_marks.htm

Posted on Apr 16, 2010

Testimonial: "tHANKS, tHIS WILL DO THE JOB."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Timing marks 1993


spark or cam ?????????????????
and which engine, some cars have up to 10 choices.
most are about 3 or 4.
not of this can i guess.

May 29, 2014 | 1993 Pontiac Grand Prix

2 Answers

Problems of gm


You can rotate the cam/crank into a positon that will not move as you remove the old belt, as long as the new belt places the cam/crank in same position as the old belt had them, it don't matter where the timing marks are. Leave your old belt on, rotate to a position that will not move or have tension on belt, (no matter the marks) and replace the belt. Make sure to recheck timing marks after new belt is installed by rotating the crank/cam back to timing marks, or just trust that the belt was replaced without the cam or crank rotated. Easy off, easy on, just make sure the cam/crank are still in time as the old belt had them located. NOTE: timing marks are there in case of a broke belt, or for a car that has jumped time. As long as cam and crank are held in same positon, and car was in time before the procedure, it don't matter where the timing marks are at during belt replacement.

Dec 15, 2013 | Cars & Trucks

1 Answer

Set camshaft timing


there should be marks on crank pully and cam belt pully. rotate motor until crank pully timing mark is on zero.the cam belt pully should be lined up with its own mark.number one piston should be at the top of its stroke (top dead centre TDC) and number one valves should be shut. if the cam belt mark is not alined with its own mark remove the belt realine the marks and refit the belt

Sep 15, 2013 | 1993 Subaru Legacy

1 Answer

I need the timing marks on the fly wheel on a 2.8d gwm steed


I want to do timing on my gwm steed after replasing my diesel pump

Aug 07, 2013 | Cars & Trucks

3 Answers

How to set timing when you relesh tensioner and it changes the alignment postion of pullies 2000 ford ranger 2.5 l


Here is the trick. Align marks. Put the timing belt on the crank shaft pulley first, and after on the overhead cam pulley. Release tensioner and rotate the crank shaft till the timing belt makes two full circles. Try to align marks, you will be at least one tooth off. Align the crank shaft on the mark, and find out how many teeth you are off at the cam shaft pulley. Count the teeth. Remove the timing belt from cam shaft pulley only. Move cam shaft pulley in reverse according to the number of teeth you counted. Make sure the crank shaft pulley is on the mark. Mount the belt at cam shaft pulley.Rotate the belt two circles and check the marks. Repeate this procedure til after releasing the tensioner, and rotating the timing belt two full circles, the mars will be align.

Nov 22, 2010 | 2000 Ford Ranger SuperCab

1 Answer

Timing OK?


You did it the right way. If you tried to make a full cam revolution you would have hit the pistons with the valves. Put the lower timing cover and crank pulley back on. If the cam marks are aligned right and the mark on the lower timing cover lines up with the mark on the crank pulley, you're good to go.

Mar 12, 2010 | 1999 Audi A4

1 Answer

Timing Belt Markings


Mark are on the crank and cam timing gears. Cam gear mark at 12 o"clock crank gear mark lined up with TGC mark on block when installing timing belt.

Dec 16, 2008 | Hyundai Motor 2002 Elantra

2 Answers

2001 pt cruiser broke timing belt


CHECK AUTO ZONE .COM FOR TIMING PROCEEDURE. I HAVE DONE THIS & IT IS VERY HARD TO GET TIMING MARKS PERFECTLY LINED UP. TOOK ABOUT 3 TRIES. ( CAMS WANT TO MOVE DURING PROCESS.) WHEN TIMING IS JUST RIGHT , IT WILL RUN. MAKE SURE BOTH CAM SROCKET ARROWS ARE POINTING UP. THERE IS A TIMING MARK IN THE VALLEY OF THE EXHAUST CAM SPROCKET TEETH THAT I MISSED.YOU HAVE TO START WITH EXHAUST CAM TIMING MARK JUST BELOW INTAKE CAM SPROCKET TIMING MARK & THEN WHEN BELT IS COMPLETELY ON , MOVE EXHAUST CAM TO TAKE UP SLACK IN BELT. IT WORKS !!!

Nov 28, 2008 | 2001 Chrysler PT Cruiser

1 Answer

Timing belt marking


The timing marks are just above the cams at the "twelve o'clock position"

If necessary, align the timing marks.
NOTE When aligning the cam pulleys with the seal plate marks, align the left cam pulley “I” mark and the right cam pulley on the “E” mark.

WARNING When aligning the timing marks, do not turn the timing gear counterclockwise. Damage to the engine will occur.

Oct 17, 2008 | 2000 Kia Sportage

2 Answers

Belts


Timing belt has marks on it that refer to the cam marks and the crank gear. Looking at the engine from the front, the timing belt should drape over the two cam gears, with 40 cogs between them on the belt. The timing belt should have 42 or 43? cogs between the driver cam mark and the mark on the crank gear. The way i've installed mine is to put the belt on the driver side cam and crank, and then put it on the passenger side cam. You'll need to lock the tensioner clockwise about 70-80 degrees to get enough clearance to install the belt.

Aug 15, 2008 | 1995 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...