Question about Cars & Trucks

Open Question

Saa 9-3 2004 tid steering loock wheel malfunction car did not start , any advice

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 78 Answers

SOURCE: Key won't turn steering wheel not locked.

common for this key switch to be defective. Might try graphite lubricant to spray in the hole. Once you replace key switch it will have to be recoded (electronically)by a lock smith, repair shop or dealer.

Posted on Feb 13, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 mini copper s. A red steering wheel and lock show up on the tachometer. the vehicle will not start or shift out of park.


http://www.northamericanmotoring.com/forums/stock-problems-issues/215965-electric-steering-wheel-lock-malfunctioning.html

Mar 08, 2015 | 2007 Mini Cooper S

1 Answer

1988 toyota hornet is not connecting to the starter...


Hornet? Um...
Anyway, it sounds like either your ignition switch is bad, or the ground wire for the steering column is loose.

Jul 21, 2014 | 1987 Toyota Celica

1 Answer

Nissan altima steering wheel


Power steering pump would be where I would start.

Apr 20, 2014 | 2005 Nissan Altima

1 Answer

Steering Wheel hard every time i start the car


Check the power steering fluid
turn the ignition on and off 3 times (common citroen power steering fault solution)
hopefully this will fix
also check the power steering pump fuse

Mar 25, 2014 | 2008 Citroen C4 1.6i

2 Answers

After changing a battery my car cant start and steering is block what to do


Hello,

I assume your saying your steering is Locked? Try turning your steering wheel, this should release the locked position, so you can start your car!

This is an anti-lock theft protection!

Kind regards!

Sep 13, 2011 | Porsche Cayenne Cars & Trucks

1 Answer

Steering wheel locked and unable t o start


if you have a red steering wheel displayed in the instrument cluster your steering column lock has malfunctioned. this is a known issue. unfortunately it cant be replaced separately and you will need a complete steering colunm. as bad as it seems the repair is quite simple i could complete repair in about an hour not sure cost of part

Apr 30, 2011 | 2008 BMW 3 Series

2 Answers

2002 chevy truck.Code B0026


Hello and welcome. code B0026 is for a airbag malfunction. this code will require a high end scan tool, like a GM tech 2 scan tool to check out.this code is related to a deployment loop problem on the drivers side of vehicle

• DTC B0026 will set when one of the following conditions occurs:
- The SDM detects the steering wheel module deployment loop resistance is greater than 4.8 ? for 500 milliseconds. - The SDM detects the voltage at steering wheel module high signal is less than 2.4 volts and steering wheel module deployment loop resistance is 6 ? or greater for 500 milliseconds.The inflatable restraint steering wheel module deployment loop consists of a steering wheel module, steering wheel module coil, steering wheel module high signal circuit, and steering wheel module low signal circuit. Shorting bars are used on the steering wheel module connector as well as the steering wheel module coil connector which will short together the steering wheel module high and steering wheel module low signal circuits when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored.

Sep 12, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I recently replaced the steering rack do to a


one or more return fluid lines in the rack is malfunctioning.. everything will always be fine once you start moving because the system has power assist

Aug 31, 2009 | 1994 Honda Accord

2 Answers

1999 voyager plymouth


I guess the cruise control buttons are located on the steering wheel...

You have a bad clockspring (contact reel in the steering wheel), all the mentioned items (wheel mounted cruise buttons, horn buttons, airbag) are run through it.

Where the wheel is able to turn a couple of turns on either side, normal wires could not be setup to withstand this. The clockspring (contact reel) is a flat wire wound up to be able to withstand the rotation.

They are not an item I would recommend replacing by yourself, where airbag systems have a procedure which must be followed to make sure you don't accidentally deploy the bag and cause serious injury.

Aug 28, 2008 | 1999 Plymouth Voyager

1 Answer

Everytime i am driving the stering wheel loocks what can be the problem


the ignition switch is what disengages the steering wheel lock mechanism have it looked at

Aug 28, 2008 | Cadillac DeVille Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15190 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...