Question about Honda Cars & Trucks

1 Answer

Is my Honda passports rear axle suppose to move up and down during takeoff

Posted by on

  • Todd harstad Apr 25, 2017

    How would I go about checking the rubbers. Looked at them and they look fine they are not dry ir cracked and I can't seem to find any play by trying to wiggle them any suggestions



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Honda Master
  • 48,235 Answers

check suspension rubbers and loose bolts

Posted on Apr 25, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear end truck differential

takes parts , labor and skills. and takes and FSM if smart.

read it.

if the whole rear axle , member and all parts swapped.

body on jack stands,

you unbolt it, (look at it, see those connective parts, bingo)

then bolt it back in

and bleed brakes (yes put in new brakes too)

and drain and fill the new axle, with GL4 lube.(look up spec)

all the itty bitty steps are in the FSM, why not look.

i log in , and see replace page i paste it , below, you can log in too.

  1. Raise the vehicle and support it at the frame.


    The hoist must remain under the rear axle housing.

  2. Remove the rear wheels and brake calipers or drums.

  3. Disconnect the sensor connector (4X2 ABS or RWAL) (14) or sensor connector (4X4 ABS).


    Exploded view of rear axle assembly

  4. Remove the shock absorber nuts and washers.

  5. Remove the shock absorbers from the anchor plates.

  6. Remove the bolts from the pinion flange.

    • Mark the driveshaft and the pinion flange.

    • Support the driveshaft out of the way.

  7. Disconnect the brake lines at the axle housing.

  8. Disconnect the brake lines at the backing plates.

  9. Remove the nuts and washer.

  10. Remove the U-bolts and anchor plates.

  11. Disconnect the harness connector from speed sensor.

  12. Move the axle from above the springs.

  13. Lower the axle from the vehicle using the hoist.

Dec 28, 2013 | Honda Passport Cars & Trucks

1 Answer

How to remove rear transmission seal from 2000 Isuzu Rodeo(Honda Passport)

the FSM covers this.
or if in USA< login to and read.
its all there.

Jun 19, 2013 | 2000 Honda Passport

1 Answer

1999 Ford Ranger jerking in the rear

The rear brakes may have some oil on them which will cause sticking/grabbing braking. Usually from leaking brake cylinders or calipers/wheel bearing seals. Pull each wheel and check. Another problem could be a bad 'U' joint at either end of the driveline. Make sure the emergency/parking brake is fully released. It's possible that a rear axle bearing is going out, but they will make a rough sound when moving. Make sure that the spring mounts are tight. Check the oil level in the differential. Shift from forward to reverse several times to see if this reoccurs each time. Get someone to watch and listen while you do this. Hope this helps!

Mar 05, 2010 | 1999 Ford Ranger SuperCab

1 Answer

95 passport shakes when4x4 is engaged during acceleration

Bad u-joints at front driveline and/or u-joints at axle connection from behind rotors- going into front differential. Need new u-joints at either the driveline front and back (going into differential or to Transfer case) or the Left and Right side axles going into the differential. Put Locking (or "Lock-outs) hubs on front axles... WARN brand are best... about $75 a pair and you can do it yourself, easily.

Dec 28, 2009 | 1995 Honda Passport

2 Answers

I cant remove a rear axle seal to a 1999 honda passport

Axle bearing and seal are made together. It is pressed on axle.

Aug 18, 2009 | 1999 Honda Passport

1 Answer

Need instructions for repacing cv axle

The cv is changed out as a rebuit unit. Buy axle CV Replacement at parts store. Go from there. The part will tell you what you need to do. good luck.

Jun 02, 2009 | 1995 Honda Passport

1 Answer

Rear axle is bent

Type the year (2000), and make (Honda Passport).
Search for Axle Assy Rear
Ignore 4x4 and focus at 4x2.
You must know the ratio - teeth (41/10 teeth, GT5) or (43/10 teeth, S7C)
(3.2L, 6 cyl, disc), 4x2 (drum brakes), 4.10 ratio (41/10 teeth, GT5)
(3.2L, 6 cyl, disc), 4x2 (drum brakes), 4.30 ratio (43/10 teeth, S7C)
1999 - 2002 Isuzu Rodeo - Honda Passport.
You can get an USED one for $600 plus shipping.
Good Luck.

Jan 04, 2009 | 2000 Honda Passport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides