Question about Cars & Trucks

Open Question

Hi have a 1996 diahatsu midget pick up 660cc does anyone have the cylinder head torque settings and the sequence it is done in

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Junoon007
  • 1011 Answers

SOURCE: diahatsu charade g200 1996 1.3 liter

Dear Sir/madam,

Valve clearance adjustment must be performed to manufacturer'sspecifications. It is normal that the exhaust valve will have a largerclearance. Adjustment is performed by either adjusting the rocker armor placing shims between cam follower and valve stem. Most modernengines have hydraulic lifters and require only infrequent adjustment.
Valve clearance measurementValve clearance is measured with the valve closed, typically at top dead center between the compression and power strokes. The tappet will be resting on the heel of the cam lobe. A feeler gaugemust pass through the clearance space. The feeler gauge should fit inand out with a slight drag. If the feeler gauge will not fit in, thenthe clearance is too small. If the blade of the feeler gauge fits intoo loosely, the clearance is too large.


AS PER TECHNICAL MANUAL IT IS AS FOLLOW:-
VALAVE CLEARACNCE:- ( HOT)
(CB MODEL )
INTAKE.....00.20mm or 0.0078 inch
EXHAUST..00.20mm or 0.0078 inch
(CL MODEL)
INTAKE......0.25mm or 0.0098 inch
EXHAUST...0.30mm or 0.0118 inch

thanks
good luck


Posted on Aug 31, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

  • 16 Answers

SOURCE: Anyone know sequence and torque specs for a

Per Chiltons...
Step 1: 30 ft lbs
Step 2: 44 ft lbs
Step 3: Plus 90 degrees
Step 4: Plus 90 degrees
Here is the tightening sequence...
10 4 2 6 8
7 5 1 3 9

Posted on Mar 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota 2c. I need cylinder head and flywheel Torque settings


Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Torque setting head 2002 nissan maxima


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 17, 2012 | Nissan Maxima Cars & Trucks

1 Answer

I need to know the torque specs for the head gasket for a 96 3.8 chevy camaro


Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.

Use a torque angle meter to rotate each cylinder head bolt 120 degrees in sequence.

Use a torque angle meter to rotate the four center cylinder head bolts an additional 30 degrees in sequence...

I hope this helps.

Jul 06, 2011 | 1996 Chevrolet Camaro

1 Answer

Lookin for head torque specs and sequence


Torque sequence ----------- ' 9 7 3 1 5 ' ' 8 4 2 6 ' ----------- Step 1: torque in sequence to 45 Ft/Lbs Step 2: torque in sequence to 65 Ft/Lbs Step 3: torque in sequence to 65 Ft/Lbs again plus 1/4 turn Step 4: Torque small bolt in rear of head to 25 Ft/Lb Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
3.3L

Feb 07, 2011 | 1996 Dodge Grand Caravan

2 Answers

What are the head torque specs?


1996 Isuzu Truck Hombre 2.2L SFI 4cyl

zjlimited_545.jpg

Fig.: Cylinder head bolt torque sequence-2.2L engine

Apply a coating of 1052080 or equivalent sealer to the cylinder head bolt threads. Install the cylinder head bolts (within 15 minutes of sealer application), then tighten them in the proper sequence first to a torque of 46 ft. lbs. (63 Nm) for long bolts or to 43 ft. lbs. (58 Nm) for short bolts and then tighten all bolts an additional 90 degree turn using a torque angle meter.

Hope this helps (remember to rate this answer).

Jan 25, 2011 | 1996 Isuzu Hombre

1 Answer

Hi i was wanting to now if anyone knows the Torque Settings for the head of a 1992 Toyota Windom V6. Thank you.


Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)

02e7fe1.gif

f910c49.gif

Oct 21, 2010 | Toyota Passenger Cars & Trucks

1 Answer

Cylider head torque specs ford windstar 1996 3,8 cylider V6


Position the cylinder head on the cylinder block. Tighten the cylinder head bolts in 2 steps following the proper torque sequence. The first step is 37 ft. lbs. (50 Nm) and the second step is 68 ft. lbs. (92 Nm).


98c7056.gif

Oct 21, 2010 | 1996 Ford Windstar

1 Answer

Engine torque specs for 1996 chevy cavalier 2.2l


For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl the check the next Head Bolt Torque sequence...

------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------

Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence

*** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Hope helps (remnember rated this).

Jul 15, 2010 | 1996 Chevrolet Cavalier

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...