Question about Dodge Cars & Trucks

Open Question

How much would it cost to fix a 07 Dodge caliber manual trans. 1.8liter engine that needs a camshaft

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 412 Answers

SOURCE: Needing to locate the airbag control module '07 caliber

it is located behind the floor shifter in center console..under small piece of carpet

Posted on Jun 20, 2009

  • 1 Answer

SOURCE: need instuctions to change tail/break lights on 07 dodge caliber

popohead, if people thought it was easy, they wouldn't be here asking. Your reply is useless.

To remove the pins, look a them closely. Notice that there's two little notches cut into the cup that holds the pin. Use a flathead on each side to leveredge them out a little. If that doesn't work at all, you can use a pair of pliers to firmly grip the head of the pin and pull straight out. Quick firm pull.

Once the first pin comes out, the second pin should easily come out. At that point, firmly grip your taillight housing, and pull straight back: Don't try to wiggle it out, and don't try to lift it to one side or the other like a trunk or door. Just pull it firmly straight back like you would a dresser drawer.

Once it's out, the little wiring harnesses come out of the taillight housing with about a 1/4 turn, and the bulbs just slide straight out of those.

Good luck!

Posted on Nov 01, 2009

cmcduncand
  • 714 Answers

SOURCE: 07 Dodge Caliber alternator

$270.00 to $300.00

Posted on Feb 12, 2010

  • 12 Answers

SOURCE: how do i install a alternator for a 07 dodge

you will need to disconnect the negative battery cable at the battery, remove right front wheel, remove underbody air dam, remove accessory drive splash shield, remove the accessory drive idler pulley. Next loosen the lower mounting bolt, then loosen the a/c compressor and relocate(pull down and to the outboard side of the vehicle to make room for the alternator the come out) next uplug field circuit from alternator and the B+ terminal nut and wire. remove upper mounting bolt on the alternator and lower mounting bolt. relocate the terminal to the other side of the a/c line. Rotate alternator pulley down and slide down and out of vehicle. Yes, its a pain in the ****.

Posted on Mar 11, 2010

roniecon
  • 6826 Answers

SOURCE: where is the radiator fan relay for a 07 dodge

Not sure,but look on drivers side below radiator.

Posted on Jul 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 dodge caliber cranks won't start no spark changed crank sensor still won't start


I need to know what fault codes you have in the memory of the powertrain control module. Also which engine you have. If you have not run a fault code test rent a code reader and do the testing, the diagnostic link connector is under the dash on the drivers side.

Feb 01, 2017 | 2007 Dodge Caliber

1 Answer

I washed my engine now the check engine light is


need to scann the car to foult code

Sep 08, 2014 | Cars & Trucks

1 Answer

07 dodge caliber throttle control


Usually replacing the TPS - throttle position sensor will get rid of this issue.

Mar 31, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

07 Dodge Caliber, ETC light


Try replacing the TPS first, then if your light doesn't go off, take it to the dealer.

Mar 31, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

On my 07 dodge caliber a lightening bolt appeared between 2 lines and the check engine light came on but everything ran fine. Please advise. Thank you


Have a repair shop check for codes every time
any light comes on your dash

Then you know if any systems have a fault & if you
should continue to use it prior to repairs

Nov 15, 2012 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Hi i have a 2007 dodge caliber with check engine light on- the error code is p008 - can you help me understand the issue?


could that be P0008? I'm not showing the code you've listed, but if you reply to this feed I will help you out If it is the code I listed, then its this , P0008 Engine Position System Performance (Bank 1) This error basically means the engine is out of Sync.The Camshaft and Crankshaft are out of position or at the very least think they are. Engine timing may be out and thus your engine is in danger of complete destruction. At the very least a camshaft sensor maybe down. Take the vehicle to a mechanic so they can check the timing issues

Aug 12, 2011 | 2006 Dodge Caliber

1 Answer

Needing to locate the airbag control module '07 caliber


it is located behind the floor shifter in center console..under small piece of carpet

Jun 16, 2009 | 2007 Dodge Caliber SXT Sport Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...