Question about Chrysler Cars & Trucks

1 Answer

Is there away to reset 1991 chrysler lebaronBody control module

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 285 Answers

Try unhooking the battery to reboot

Posted on Apr 25, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Odometer works but speedometer does not. 1991 chrysler fifth avenue. can speedometer reset w/o changing original odometer reading? how to.


Y can't reset the speedometer. Your problem is the electric motor that turns the speedometer needle. I believe yours just pops in and out. But some are soldered. You can get both kinds on line.

Jan 17, 2015 | 1991 Chrysler New Yorker

1 Answer

What this cdes maen36/46/53/54


code 36 air switch solenoid circuit non turbo or wastegate solenoid circuit on turbocharged models.
code 46 battery voltage too high. code 53 module internal problem SMEC SBEC failure internal engine controller fault condition detected. code 54 problem with the distributor synchronizer circuit.

Jul 15, 2013 | 1991 Chrysler LeBaron

1 Answer

My 2001 crysler sebring convertible is shifting hard. the guy up at autozone says its the shifter control module. anyboyd know where that is ?


It doesn't have a shifter control module. It has a transmission control module. But the problem you likely have is that you need to run a quick learn reset on the TCM. You will need a scanner to do this or have a shop do it for you. You need to reset the adaptive memory of the TCM and run it through quick learn.

Dec 08, 2010 | 2001 Chrysler Sebring

1 Answer

Where is the ignition control module located on a 91 dodge ram pick up truck with a 5.2 engin


Part of the PCM/Computer,I know they had a different name for that, on a chrysler product,not separate item you can replace.

Nov 11, 2010 | 1991 Dodge Ram 150

1 Answer

My 87 chrysler has rough idle when sitting at stop lights and stalls slight hesitation sputter when accelerateing


It's the lean burn system that's probably the problem. If you replace the Engine control module/computer then it should solve your problem at least temporarily. I know there is a conversion to get away from the lean burn system for good, but I have not tried that out myself yet. But my engine control module seems to go out during extreme weather.

Sep 20, 2010 | 1987 Chrysler Fifth Avenue

3 Answers

The power locks have stopped working, what can do to fix it?


I had the same problem with my 2005 Town & Country Limited, and the dealer didn't have a clue what was causing it. After doing some research, I found the fuse (20 amp) that's associated with the door locks and unplugged it for about 10 seconds, and then plugged it back in. The fuse was not bad, but seamed to reset the system. Give it a try. It's simple and free. Good luck.

Mar 19, 2010 | 2005 Chrysler Town & Country

1 Answer

Its a 91 jeep cherokee 4.0 it turns over but will not start there is no spark. I have replaced the coil but still nothing


No spark usually is caused by coil (which you already replaced), ignition control module, or pickup coil inside the distributor. The coil and the control module are the most common. The control module is located just outside the distributor, you may be able to take it off and have it tested at the dealer. The pickup coil is inside the distributor, unfortunetly there's no way to test them. Also check plugs and wires if they haven't been replaced in awhile.

Nov 07, 2009 | 1991 Chrysler Town & Country

3 Answers

My 2005 town and country power door locks have lost power. Where is the fuse for the door locks? Is there something else I should be looking for other than a fuse problem?


2004-2005 CARAVANS HAD A SOFTWARE ISSUE IN BODY CONTROL MODULE..HAVE YOUR VEHICLE SCANNED AND SEE IF BODY CONTROLLER WILL TAKE A SOFTWARE UPDATE AND IF ANY FAULTS PRESENT..AS FAR AS I KNOW,DEALER CAN ONLY UPDATE CONTROLLER SOFTWARE

Jun 26, 2009 | 2005 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

568 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

71694 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7031 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...