Question about Cars & Trucks

1 Answer

I cannot get the water chamber out no matter how hard I try. I'm thinking of busting this piece of junk with a hammer.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,045 Answers

That's a good solution. Have googled for that disassembling instructions?

Posted on Apr 25, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 1997 BMW 328i. It will not start wont even make a noise when turning key. Tried jump but didn't work. Hit the starter with a hammer. Changed battery. Lights work radios works just won't start...

try removing the spark plugs to ensure that you do not have a hydraulic lock in a combustion chamber. This happens when a crack or faulty head gasket allows water into the chamber and when the piston comes up it is prevented from going over the top of the stroke. Removing the plugs allows the water to come out and the engine to spin.

Aug 25, 2013 | 1997 BMW 328

1 Answer

Where is the freeze plug on 1990 Honda prelude si 4ws 2.1 vtec

freeze plugs are located along the block on any engine. it's a indented circle piece of metal that is press fit into the block along the water jacket so that it ill bust if the coolant freezes rather than busting your block. they usually rust rather than bust

Nov 15, 2011 | 1990 Honda Prelude

1 Answer

My bronco2 wont start. Just replaced both fuel pumps, fuel filter, battery, fuel injector modal, I've tried to locate the restart button, think i've found it but it was broke. What do i do now or what is...

starter if engine wont crank....otherwise if it turns over but no start then it could be electrical maybe ignition module.if starter no work tap with hammer while trying to start they get hung up or on a flat spot an that usually jars them free...try electrical first pull one spark plug and see if when you trun it over the spark jumps the plug if it does then it is a fuel problem...dont hold spark plug wire position it to lay away fro everything...nobody likes gettin shocked no matter how funny it is after.....

Mar 19, 2011 | Ford Bronco II Cars & Trucks

2 Answers

Overheating 1985 k5 350 engine, leaking coolant, all water hoses, thermostat & waterpump replaced. possible leak above starter, also maybe a freeze plug, leak hard to find. please advise

Never, never, never use 100% water in a cooling system. Always. always, always add 50/50 antifreeze/water solution so that the CASTING pluggs don't rust or freeze (they are NOT freeze pluggs). If it froze with water in it you have a 75% chance that the motor is junk; 25% chance that you can fix it by replacing the CASTING plug. I drill a small hole in them and screw my sliding hammer in and pop them out (nearly impossible in the vehicle). Adding water to a cooling system is NOT cost effective. Ray (garage owner)

Sep 20, 2010 | 1985 Chevrolet S-10 Blazer

1 Answer

I too am having a problem removing the small metal piece from the back of my 2002 pontiac grand prix rear view mirror. It fell off the windshield due to the heat, I'm supposing. It has the Onstar...

It should be the same as the ones from the late 90's. You have 3 pieces there. The metal piece comes out the bottom of the mirror and should have a piece of plastic attached to it. It is a friction fit with the actual mirror so it shouldn't require a lot of hammering or even hard hammering.
Once the mirror is off there should be a small slot in the remaining plastic and metal. Use a small screwdriver or something similar to push in on a clip that is inside and the plastic and metal should separate. Hope this helps.

Aug 10, 2010 | 2002 Pontiac Grand Prix

2 Answers

Object fell into water jacket

Yes it may hurt the impeller (blades) on waterpump or plug a coolant passage. Try a magnetic retrieval tool through whole you saw it fall through. Or above it through passageway in intake manifold or you have to pull off that plate between waterpump & engine.

Jun 06, 2010 | 1996 Ford Thunderbird LX

1 Answer

Bmw 3 series water pump just wont budge both jacking holes have busted its that tite

Spray PB Blaster all around and let it soak, then using a pry bar put some pressure against the pump like you are trying to pry out the pump. Take a hammer and tap on the pump all around while praying out, the rubber "o" ring is swelled and corroded.

Apr 25, 2009 | 1996 BMW 318

3 Answers

I have a 1996 mitsubishi eclipse and it overheats real fast. I changed the thermostat and don't think its's the water pump so what can ut be?

You should have what is known as a TK head test done.Very effective in isolating wether you have combustion chamber gases escaping into the cooling system.Take all the spark plugs out and check to see if there is any sign of water on them.Is the fan working correctly?

Oct 30, 2008 | 1991 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides