Question about Cars & Trucks

Open Question

Which bolts do we undo, to fit it through a doorway?? pics would be helpful, thx

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove fan clutch and will f150 1997 ford f150 4.2 liter fan clutch fit the dodge


undo the fan off the hub and undo the hub off the water pump
When you have it off compare the two
items like fan bolt holes and bolt holes for the pump will be telling factors

Mar 13, 2015 | 2005 Dodge Dakota Quad

1 Answer

I have pulled the starter off my 98 vw jetta gls and installed the new one but the bolts will not go in the mount


Hi
Undo both bolts and make sure the statermotor is fully home before fitting the bolts. Dont tighten the bolts fully, fit them by hand first then tighten up.
These are steel bolts winding into alloy housing so dont over tighten.
Make sure the wiring loom is clear too.
Roger

Apr 14, 2014 | Cars & Trucks

1 Answer

Engine thermostat location


follow the upper radiator hose. thats the big one that come out the top corner. and follow it to the engine. the hose will clamp onto a metal fitting. and the fitting will then bolt onto the top of the engine with 2 or 3 bolts. undo those bolts and thats the thermostat on the inside of it. just remember to drain out about 1/3 of the radiator fluid. otherwise you will have a big mess, when you undo those bolts.

Sep 25, 2013 | Chevrolet Corsica Cars & Trucks

1 Answer

How to replace Mass Air Flow Sensor


the mass air flow is located on the outside of the air box. this is where you put the air filter. undo the clamps that hold the hose onto the air box and to the throttle body. undo the bolts that hold the air box in place and remove the air box. there are 2 small bolts that hold the mass air flow to the box remove these and reinstall in reverse order. heres a couple pics to help you identify it. hops this helpsonetufshoppe_49.gifonetufshoppe_48.gif

Jan 26, 2011 | 2003 Cadillac Sts

1 Answer

How to replace front brake pads


remove the front wheels undo the lower bolt on the caliper to caliper mount lift up the caliper push the pistons back with a clamp remove old pads fit new pads swing down the caliper and fit the bolt back with lock tight on the thread and tighten the bolt to 35nm

Aug 11, 2010 | 2005 Kia Sorento

1 Answer

How do I change the oil


there is an oil drain plug (BOLT) under your car on the bottom or side ( edge) or the oil pan. get yourself a catch can like some sort of plastic bucket that will fit. Undo that bolt and let it drain. Undo the oil filler cap under your hood on your motor so that it drains more completely and faster. I reccommend changing your oil filter which usually just unscrews, you may need a strap wrench to help it off, prepare for some spillage. Put new oil filter on, put the oil drain bolt back in ( usually with a new washer, you dont have to but it is recommended) and pour however much oil your car calls for, into the oil filler hole. Get yourself some rags and a funnel to help :)

Mar 12, 2010 | 2001 Honda Odyssey

1 Answer

Himself has tried to replace the battery on the 03 frelander. managed to get the top bit holding the battery off but the bolt holding th batery into the clip won't undo - just spins around any ideas?!


If you are talking about the battery clamp bolts turning, then put a screwdriver in the split of the clamp and try to put turning pressure on the screwdriver and at the same time undo the nut of the clamp bolt. Or if you have a pair of mole grips, clamp the bolt head and undo the nut. Worst case , pry the clamp off the terminal and use a hacksaw and cut the bolt in half and remove it , fit a new bolt after. Hope that helps

Feb 04, 2010 | 2003 Land Rover Freelander

1 Answer

Need help fitting a clutch on a VW GTI Golf


undo centre wheel hub nut 30mm/32mm, socket. undo lower wish-bone outer bolts, disconect battery,/remove starter motor,/remove transmission mounting bolts to body frame ,/ remove all surrounding bolts around bell housing transmission,/ remove clutch cable from transmission,/ remove drive shafts from centre hub and transmission,/ make sure car is standing on axle stands at front of jacking points,/use a trolley jack to suport engine sump with a piece of wood,/ slide transmission away from flywheel,/lower transmision on floor,/undo all clutch plate preasure bolts 10mm,/remove thrust bearing located on centre transmision shaft ,.also make sure if fitted speedo cable needs to be removed.new clutch plate should indicate flywheel ,without fitting clutch plate wrong way round/otherwise transmision will not bolt to engine block.,

May 17, 2009 | 1999 Volkswagen GTI

2 Answers

How do you remove and replace the radiator of a 1997 EL Ghia?


first undo the hoses, there are 4 water hoses and 2 oil hoses, the bottom hose is difficult on the high side because of the alternator.
un plug the 2 wire connections (don't forget the locking tabs) then undo the air duct held by 2 screws. followed by 2 bolts located on the top of the radiator and lift the fans straight up
there are 2 larger bolts that hold the radiator in at the top. lift straight up.
when replacing be sure to place in locators in the bottom of radiator and fans

Mar 08, 2009 | 1983 Ford Fairmont

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...