Question about Cars & Trucks

Open Question

3.5kg/cm torque to hp looking for ele. 12 v motor strong enough to raise pop up camper needs to be low rpm

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Weak Torque?

Get the Banks chip and 4" exaust with a truck muffler. It will amaze you.

Posted on Aug 28, 2008

  • 3301 Answers

SOURCE: engine sputters at low rpm,

if your towing it will heat up faster,, watch the rpm's ,, if you need to downshift during uphill climbs do so,, keep the RPM's a little higher than normal, as far as the sputtering,, that could also be due to the towing and extra weight on the motor,, it could be that some of the components are weak, and towing just makes you notice them more, check the cap for build-up on the contact points, and also, the rotor , depending on the miles already on your plugs they too could be at the end of their life cycle, with the over heating, make sure you have a good mix of antifreeze and water in the radiator, and make sure the fan is functioning properly

Posted on Aug 07, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How many Hp in a 71 Winnebago 454 motor

Not much horsepower but a LOAD of low rpm torque because of the RV camshaft used in a motor home engine.

May 09, 2018 | Cars & Trucks

1 Answer

How maximum increase horse power output force of inductiom motor of 2hp using loadwheel or flywheel and how much hp force it can be increase. Plz describe detail.

induction motors develop max hp at the set RPM and current setting according to the windings in the motor. The use of flywheels in the system help the motor to hold steady rpm when a sudden load is applied as the stored energy in the spinning flywheel overcomes the sudden draw of power and stops the loss of rpm's . If you want more HP get a bigger motor.. ( HP is now an irrelevant term as it not an accurate to describe the motor's capacity . The definition is now torque or the ability to turn a shaft That is why older motors were bigger and used more current than the smaller motors that produce more torque for less current

Nov 22, 2013 | Cars & Trucks

1 Answer

Need to know what gas engine delivers 105 ft.-lbs. of torque at chrankshaft at what rpm?

1 hp =550 ft/lb of torque so you would be looking at a 1/4 hp engine like a lawn mower engine tiller engine or small pump engine . Most of these develop the torque at around 2500 rpm. As to the brand or make each maker uses a different stroke for the piston which alters the torque for the rpm.

Sep 23, 2013 | Cars & Trucks

1 Answer

1994 corvette running too rich black smoke and coughing low rpm

the brake servo needs refitting and ensuring correct torque

Jun 11, 2013 | 1994 Chevrolet Corvette

1 Answer

Motor size 1996 hundai

1996 Hyundai Accent ENGINE SPECIFICATIONS 1.5L 92 hp I4 Horsepower 92 @ 5500 RPM Torque (lb-ft) 97 @ 3000 RPM Fuel Type/System Gasoline/MPFI Valves/Valve Configuration 12/SOHC Displacement (cc) 1495 Bore X Stroke (in.) 2.97 X 3.29 Compression Ratio 10.0:1 Turbocharger No Supercharger No

Mar 25, 2011 | 1996 Hyundai Accent

1 Answer

New Power steering pump but no p/s @ low RPM

Don't think the pressure switch would do that. Sounds more like a bad pump (they have people that can't tie their own shoes building this stuff thanks to outsourcing to other countries) Failure rate on rebuilds is far higher than it used to be. Reason I believe the pump may be the problem is that it does seem to work at high rpm's...tells me that it either has an internal pressure bypass or not making enough pressure. Could be wrong, but I'd get another one first.

Jul 13, 2009 | 2001 GMC Yukon XL

1 Answer

Bolt torque for 2004 camshaft and crankshaft gear

if your installing your crankshaft the Torque: 27 N·m (275 kgf·cm, 20 ft·lbf). And for your camshaft the 25mm bolts [2] are 7.5 N·m (80 kgf·cm, 69 in.·lbf) and the rest are 16 N·m (160 kgf·cm, 12 ft·lbf)

Jun 27, 2009 | 2004 Toyota Sequoia

1 Answer

No low down torque 1600 16 vaule fxgt

The 4AGE does not start making good power until you get to 4200 RPM when the TVIS kicks in.

"112 hp (84 kW) at 6600 rpm and 97 ft·lbf (131N·m) of torque at 4800 rpm in the American market."

Apr 10, 2009 | 1987 Toyota Corolla 2 Door

1 Answer

Increasing Torque in Grand Vitara 2007

If it's a fuel injected motor u coukd add better software
Can also flow and port the head
Will get at least 10% overall increase

Mar 07, 2018 | 2007 Suzuki Grand Vitara 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides