Question about Cars & Trucks

Open Question

LF parking light not working.RF parking does & L+R sigs work.New bulb,socket like new cond,I even bent pins on bulb so they were sure to make contact in socket.Volt ok at all 4 harness pins.Still no.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: 2003 dodge ram 3500 4x4.

first thing to do, go with the replacement of the light bulbs, high beam and low beam are two different fillaments on the ligh bulb, as for the rear also replace the bulbs, when your flasher rellay flashes faster, it means that there is less drop of current in the circuit, like only one light bulb working.

Posted on Dec 07, 2008

Ad
emissionwiz
  • 76630 Answers

SOURCE: 2002 F150 brake/turn signal

if u checked all the fuse's both in the cab and under hood and the wiring harness at rear of truck for any damage, I suspect the turn signal switch is defective.

Posted on Mar 05, 2009

jasperoni
  • 203 Answers

SOURCE: LT signal fault

It is very difficult to diagnose your problem without being in front of your vehicle. But I will let you in on a tip-This vehicle substitutes bulbs for inoperable bulbs i.e. if your brake light goes out the bulb monitoring system will substitute your tail lights in place of the inoperable brake light. It can be frustrating you are not very familiar with your vehicle because when the brake switch is depressed you will see lights on and still get the message on the heads up display. also it is very important that the bulb wattage is exact. any difference in resistance will trigger a inop bulb problem. Also I believe that the turn signal is a dual filament bulb-one for turn signal and the other for your running lights. hopefully I have been helpful

Posted on May 30, 2009

  • 521 Answers

SOURCE: 1991 Chevy Corvette Convertible: 3rd. brake light

make sure you have the correct bulb and have it installed in the socket correctly.

Posted on Nov 15, 2009

  • 2418 Answers

SOURCE: Need to solve towbar wiring fault for trailer

This sounds a bit crazy, but you do not have a good solid ground to your trailer brake lights. You may have to run a separate ground wire from the trailer to the car. Pull your trailer close to the front of your car, close to the battery. Use some wire to connect your trailer to the battery. Then touch each contact one at the time until you learn which port turns on which light(s). Using the wires, only one in the ground connector and the other in the brake connector. gain access to one or both sides of the trailer lights, use another wire and touch the base of the bulbs to the metal of the trailer if the light gets brighter you need to run another ground wire. Hope this helps FixYa up.

Posted on Jul 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lf rear turn signal not working. LF front, RT front & rear working. Replaced with 3 new bulbs but no joy. What would cause one blinker to not work?


This could be a fuse so check them all, next make sure you are not missing a burned out light or have the wrong bulbs in.

Replace the flasher unit, make sure the connections in each socket is clean, make sure the wires are in good order.

Also the switch control might be at fault.
hope this helps.

Mar 18, 2015 | Cars & Trucks

2 Answers

2006 Jeep Commander Tail light


The tail light circuit is separate from the brake and turn signal circuit. Either the bulb socket has gone bad or a wire has flaked out. Check for voltage at the socket on either pin base when you have your parking lights on. If voltage is present, it is either a worn socket failing to hold the bulb properly, or another bad bulb. If no voltage, determine which wire on the other side is tail light power, and run a new wire across to the side that isn't working and connect it to provide power.

Apr 09, 2014 | 2006 Jeep Commander

1 Answer

One metal contact not working in light assembly of right rear turn signal


Must be a bad socket, anyway. If I understand, you are talking about the two contact points inside the socket? On a two filament bulb, one contact is for the smaller filament park light, and the other contact is for the turn signal and/or brake light, the larger filament inside the bulb. So if you tested with a test light, with park lights on, one contact only would light up the tester. If you pressed the brakes, the other contact would have a steady light on the tester. That same contact would or should have a blinking test light, with the key on and the right turn signal on.
I would not be surprised if you need a new assembly. Possibly, too, the ground for that side needs checked.

Jan 29, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Rf highbeam doesnt work,after new bulb install 02 monteSS


Check for 12VDC at the connector with your high beams on. Could be the wiring or the connector and no they run on the same fuse.

Dec 30, 2012 | Cars & Trucks

2 Answers

My right side taillight does not come on, but they work when the brake is pressed as brakelights. Do I need to put new lamps in, or find whatever fuse ?


The bulb has 2 filliments in it ,one for the brake light ,the other for the park light,
I imagine the bulb is bad.

Sep 06, 2011 | 2002 Chevrolet Malibu

1 Answer

The boot light will not work even with a new bulb


Fast solution:
Assuming all fuses are OK.
Check the filaments (look for a broken filament wire) in the old bulb to make sure it's a bulb problem. If the old bulb is truely defective, check the new bulb to make sure it does not have a broken filament. If the bulb looks OK, take a look at the socket to make sure that it is not rusty or corroded. If the socket contacts are not clean, take a small piece of fine sandpaper and clean both the center contact and the inside of the socket.
If you have tried these things, and the light still does not come on, you'll have to do a continuity trace of the wiring to fine where the power to the bulb is being interrupted.

Jul 13, 2009 | 2004 Ford Fusion

1 Answer

2003 dodge ram 3500 4x4. low beam RF works no LF; high beam RF out, LF works. turn signals onlr RR works no LF,RR,RF. quickflash on dashboard


first thing to do, go with the replacement of the light bulbs, high beam and low beam are two different fillaments on the ligh bulb, as for the rear also replace the bulbs, when your flasher rellay flashes faster, it means that there is less drop of current in the circuit, like only one light bulb working.

Dec 07, 2008 | Dodge Ram 3500 Cars & Trucks

4 Answers

Right turn signal flashes too fast


Usually this is caused by a burnt and melted bulb socket (look inside the socket at the bulb contacts), you have to replace it with a new-revised bulb socket, which entails cutting the wiring harness and splicing a new socket. This is a factory deffect which GM refuses to acknowledge.

Jul 16, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...