Question about Cars & Trucks

Open Question

Removing front drive shaft 1992 bayou 300 4x4

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 46 Answers

SOURCE: Front drive shaft on Jeep Grand Cherokee

yes but make sure you don't in gauge the front axle

Posted on May 19, 2010

  • 7353 Answers

SOURCE: clunking - rattling noise coming from my front drive shafts when i drive over bumps in my 1992 Ford F150?

If its 2wd, there are no driveshafts. check the sway bar links/ and bushings,

Posted on Mar 15, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front diff.seal leaks


Remove the front drive shaft remove the drive yoke off the pinion shaft remove the old seal install new seal install front drive shaft. PS check pinion bearing play before removing drive yolk. if it is loose then you might also need bearings

Oct 21, 2015 | Ford Explorer Cars & Trucks

1 Answer

Cv boot failure


The best thing to do is completely remove the front drive shaft (assuming you are talking about the front CV boots).
1) Jack up the front end of the vehicle.2) Remove front wheel(s), track rod ends and slacken [don't remove completely just yet] the centre hub nut and remove split pin.3) With the gear in neutral, and using an appropriately sized round punch and hammer, punch out the location pin from the drive shaft where the drive shaft meets the gearbox output shafts.4) With the assistance of a flat screwdriver, lever and pull the drive shafts off the gearbox output shafts and let them drop down. 5) Using a rubber mallet, hammer the drive shaft through the front hub. You kept the nut on the end of the shaft initially so as to prevent damage to the drive shaft threads during hammering. This nut will have to be backed off and eventually removed as the shaft slides through and out of the hub unit.
With the entire shaft removed from the vehicle:
1) Cut off or slacken and remove any rubber boot retaining clips.2) slide the rubber boot(s) towards the centre of the shaft.3) Remove the inner joint first by using a small, flat screwdriver to flick out the retaining wire from the inner lip of the joint. (Keep this wire)4) Slide off inner joint cup and clean.
5) Locate the spring clip from the inner end of the shaft and carefully remove without over-stretching. if you have no replacement.
6) Slide off inner C.V. joint, and clean.
7) Remove damaged boot(s), clean all components, re-grease with LM grease and replace.
8) Reinstallation is the opposite of removal steps.


Note: Take care when re-installing drive shaft to gearbox output shaft. This will usually only align to a single position. Before tapping retaining pin back into place, visually inspect alignment of the shaft's holes. You can use your round punch to help align the holes before re-installation of the retaining pin.


Tip: With the removal of the front drive shafts, it may be a good opportunity to also replace front gearbox output oil seals and front wheel bearing-drive shaft dust seals. These are fairly inexpensive and may prolong the life of components as well as reduce the need for repetitive removal of parts.

Nov 03, 2012 | 2003 Subaru Baja

1 Answer

Replaceing the front seal in transmission


You will have to remove the transmission.that would include removing drive shaft ,possibly exhaust.

Apr 07, 2010 | 1992 Mercury Grand Marquis

2 Answers

Can i drive my 1992 gmc jimmy without the front differentical? And if not where can i buy one for cheap?


Yes you can drive without front differential. Easy way to do so is just dissconnect your front cv axles. Just make sure you dont throw that car into 4 wheel drive.

Mar 10, 2010 | 1992 GMC Jimmy

1 Answer

92 wrangler wont go into four wheel


If you have an actuator box on the passenger front axle that may be disconnected or broken. If not remove the cover from the front differential and check the gears...they may be broken.

Jan 13, 2010 | 1992 Jeep Wrangler

1 Answer

How do you remove the drive shaft from a 1992 Geo Tracker?


for 4X4 there are two drive shafts one to the front axel and one to the rear they are bolted to the axels with four bolts and four nuts undo those and gently wiggle the driveshaft from the transfer case. make sure it is in park it makes it easier...

for 2 wheel drive same thing for the rear just wiggle it from the transmission there is no transfer case. just as a warning some gear oil or tranny fluid might leak if the car isnt level

Dec 27, 2009 | 1992 Geo Tracker

1 Answer

How to replace front drive shaft ?


Mark the drive shaft postion to the transfer case and front axle. Remove the bolts/straps from the transfer case and front axle pinion that hold the drive shaft in place. Remove drive shaft. You may have to drop the exhaust pipe for access.

Jun 02, 2009 | 1997 Dodge Dakota

1 Answer

4 wheel drive light is on in my jeep


vacumn pod on the front axel is stuck on. Jack up the front wheels spin both tires at the same time and see if the front drive shaft turns. If it does the 4x4 on the axel is engaged. The front drive shaft on these should not turn when vacumn pod is disengaged. YJ's have a split axel on the right side inner axel shaft.

Apr 10, 2009 | 1992 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...