Question about Cars & Trucks

Open Question

Screen assembly not on bottom track and will not come out. Where do we go from here?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pass Window Wont Roll Up, But it rolled down, and if you lift it up, then hit button to go down, it rolls down... drivers window rolls down, then you have to play with the switch to get it up again, s


Qsmoma:

If the window closes when you play with the switch, the switch is probably ok. The window may have jumped out of the track or the track is damaged. Pull the inside door trim and check the track and mechanical arms that extend from the bottom frame of the window.

Nov 22, 2014 | Cars & Trucks

1 Answer

2007 yukon denali back window might of came off track w


The window motor and regulator are one unit. There is a known defect with this assembly. The regulator assembly cable breaks. The regulator needs replacement. This causes the window to become dislodged from track assembly.

Apr 17, 2014 | 2007 GMC Yukon Denali

1 Answer

How to change front power seat track worm in 1993 landcruiser


Lift the front edge of the seat bottom by using the regular power seat switch. Take voltage readings of the seat slide motor.2 Verify that the voltage to the seat slide motor on the harness side between "BR" and "W/B" is 12v when the power seat's switch is pressed backwards and forwards. Jot down your radio presets and tap the seat slide motor so that the motor will work long enough to give you access to the seat mounting bolts.3 Pull the seat as forward as it will go. Take off the two M10 rear seat mounting bolts and set them aside. Push the seat as far back as it will go. Take off the two M10 front seat mounting bolts. Switch the ignition so that it marks "OFF." Unplug the negative battery cable. Stand by for 4 minutes. Raise the seat assembly to find the harness-to-seat connectors. Disconnect them.4 Take out the entire seat assembly and place it on a dry, clean, flat surface. Position it so you can access the bottom of the seat. Undo the seat bottom's carpet flap and take out the four M8 bolts. Then, take out the top screws from the right hand and left hand side finishers. Unplug the seat sub-harness connector.5 Put both the seat rails back into their rear position and take out the worm gears, motor, flexible wire and gear boxes all at the same time. Take out the flexible wire from the gear boxes using a screwdriver. Verify that the new seat track mounting tab makes contact with the rear stopper and that the threaded shaft facing up is point upwards. 6 Install six new rubber grommets. Place the new worm gears, flexible wire and gear boxes into the frame. Reposition the seat tracks over the seat track mounting tabs. Use your hand to tighten the M6 bolts securing the seat track mounting tabs. Torque the six base plate nuts securing the gear boxes to 64 to 85 inch pounds (7.17 to 9.69 Nm) and the M8 bolts on the seat's front edge to 13 to 17 foot pounds (17.5 to 23.7 Nm).7 Plug the slide motor connector back in and hook the carpet flap's strap. Reinstall the seat assembly and reconnect the electrical connectors and negative battery cable. Torque the mounting bolts to 27 to 36 foot pounds (37 to 49 Nm). Operate the seat to make sure that the problem has been resolved

Sep 29, 2011 | 1993 Toyota Land Cruiser

1 Answer

1993 Chevy Lumina APV drivers window off track. Seems to missing something to stay in the track. There is a holeat top corner and a hole at bottom corner like it is missing a bracker of some sort. It is...


break out some paper clips and try to fix it, but really i would just buy new car or not worry about it

also there is ebay(for the assembly(the replacement parts))

Jul 15, 2010 | 1993 Chevrolet Lumina APV

1 Answer

The dish washer do not spray water,there is water in the machine


Do you hear the pump run when it is supposed to? If so, you need to tear down the lower spray arm assembly to the deck. (keep track of orientation and placement of each part) At the bottom, you will find a large screen that must be removed and soaked in hot water/white vinegar/detergent for an hour of so to remove water and food deposits. Scrub the screen lightly to help clean it. Check all openings in the deck area for any food plugging--vacuum them out with a wet/dry vacuum. Reassemble all parts in reverse order--inspect all spray arms for hole plugging and any split seams. Hope this helps!

Nov 28, 2009 | Cars & Trucks

1 Answer

How do i change the frequency on my car radio


At the bottom of your info screen you will see a series on almost square selector buttons, these select your channel presets and slightly below them above the cassette player and left of center will be your tuning/track buttons with little arrows for channel up or down. Select your preference a.m. or f.m., then with the tune /track buttons, then use the buttons to tune to the desired station. then push and hold for 3 seconds on the button position at bottom ledge of the info screen to lock your selection.

Oct 28, 2009 | 2000 Lexus RX 300

1 Answer

Broken driver seat track bracket hinge assembly


track its self bolts on after u take the seat out turn it upside town and un bolt the track u can pick them up at any junk yard or salvage yard

Oct 08, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Automatic Side door starts but does not open, using either the key button or the interior buttons. What are the usual causes and how much is the repair


It is usually the wire track in the bottom of the door jamb area. A break in one of the wires in the track opens slightly upon movement of the door and it no longer responds. Replace the wire harness/track assembly. I'm not sure of the price of the part, but the replacement procedure is pretty simple. I hope this helps.

Aug 18, 2009 | 2005 Dodge Caravan

1 Answer

Window glass slipped off of track


Check the regulator, it is not anything electronic it is the bar and cable assembly the window rides on and sometime the end ears crack off. This is more typical of imports than american cars, but every time that situation happened to me it was the regulator, not that the window just slipped off the track.

To check it just pop off the panel and remove the plastic barrier, look in the inspection hole and see if the window is still connected to the bottom support (regulator). The motor is connected to the center of the regulator winding the cable in a different direction when the switch is acitvated up or down and if the the regulator is broken the cable is running free.

I did have a window fall out of the track once and only once in a 1987 Safari, which I was able to get back on track once I popped the panel and could get to the track and window from below or inside the door. Good Luck.

Jun 08, 2009 | 2003 GMC Envoy

1 Answer

Remove outside vent


you have to remove door glas first.the vent will come out as an assembly as part of the window track.should be bolted in three places.top of door,front side about even with glass opening,and bottom

Apr 24, 2009 | 1991 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...