Question about Cars & Trucks

Open Question

Steering froze while turning - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steering wheel froze


Power steering pump going out? check the fluid level

Sep 06, 2013 | Ford Cars & Trucks

2 Answers

While I was driving I heard a loud squealing noise then it was hard to turn the steering wheel and the battery died while I was driving. What might be causing this?


Water pump frozed and took the belt out lost alternator lost power steering. youll have to two it for repair. hopefully it was just a belt.

Apr 30, 2011 | 2003 Mitsubishi Montero Sport

1 Answer

Power steering locked up one day going down road, car died, and every since u can turn it over but it wont crank?? help!!!!


Remove the power steering belt from the power steering pump. Try to restart. Sounds like the power steering pump froze up. If the belt drives more than the power steering pump (like the alternator), you will have drained the battery and the engine will not start. replace pump, charge battery, replace belt....hopefully drive. Good luck.

Feb 22, 2011 | 1994 Chevrolet S-10 Blazer

1 Answer

I have a mercedes c240 auto but the ignition wont turn seems locked


1. Some times the keys wear out. Do you have a spair key you can try.
2. Turn the steering wheel back and forth while trying to turn the key sometime the steering wheering lock will bind.
3. Now the bummer part is the ignition lock will have to come out so you can determine what part froze up.

Oct 30, 2010 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

Replaced serpintine belt for power steering, alternator and crank shaft but belt still squeels. And appears to be tight. Slack is of 1/4 in..Is there one of these three components froze up. Power steering...


The crank shaft is not froze up if the engine is running. Without knowing how severe the situation is, it is probably best to remove the belt and feel each pulley or drive wheel to detect the condition of the bearings. It should be very clear which pulley bearing is loose by "wiggling" the pulleys. One of the pulleys will have a lot of play in the bearing. Also the pulley with the bad bearing will be hard to turn by hand with the belt off. Be sure to check every pulley on that belt circuit, except the crank shaft, you can't turn it by hand.

Sep 12, 2010 | 1998 Mitsubishi Eclipse

1 Answer

2002 Dodge Dakota squeaks over bumps and grinds on slow left turn


I HAVE A 2003 DURANGO THAT DOES THE SAME, IT IS EITHER THE CONTROL ARM BUSHINGS (UPPER AND LOWER) OR THE TORSION BARS AND/ OR BUSHINGS!!!

Jun 30, 2009 | 2000 Dodge Dakota Quad Cab

1 Answer

Steering wheel


your lock cylinder is frozen, it activated the steering lock.
have to take aparta steering colum and replace the ignition lock.

Aug 10, 2008 | 1993 Saturn SC2

1 Answer

Turn signal problems


Try adjusting your steering column tilt and see if a different position fixes it. Otherwise the switch in the steering column is most likely faulty.

Jul 22, 2008 | 2004 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...