Question about Cars & Trucks

Open Question

Part numbers for right inner and outer tines model P-FTT-160MD-(E)

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 1995 toyota landcruiser diesil headlights

inner lights are highbeam outer lights low beam and side gaurd lights are your parkers, if you are 100% sure your globes are ok then your dimmer switch is stuffed this is the light switch in the cab that you use to opperate lights, sometimes the contacts get dirty inside the switch and create a short if you are mechanicaly minded then you could have a go at pulling it appart and cleaning it. if not you could get one from the wreckers in your area......

Posted on Sep 20, 2008

Ad
  • 1 Answer

SOURCE: I have a 1977 Dodge. Model # M500, removing inner dually tire

THE INNER STUDS FOR THE INNER WHEELS ARE NUTS AS WELL AND SECURE THE INNER WHEEL. USE A SQUARE DRIVE TO REMOVE THESE STUD/NUTS. DRIVER SIDE NUTS/STUD ARE LEFT HANDED(STAMPED WITH A BIG (L)). AND PASS SIDE RIGHT HANDED. THESE TORQUE SPEC OUT @ 400-450 LB FT. OF TORQUE, YOU WILL HAVE TO USE A CHEATER BAR OR HEAVY DUTY INPACT!

Posted on Oct 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram cv inner outer mazda sting


Inner cv's hardly ever pack up it is the outer ones as it works harder in turns. it will be a clukking noise and some grinding. Make sure they are well greased and the rubber boots are not torn. if it has wear replace it as it can be costly when it fails.

Dec 03, 2013 | Mazda Cars & Trucks

1 Answer

Torque specs bearing


Honestly you should search google. It is right there. the inner hub nut must be torqued to 59 Nm rotate the hub three times in each direction and then loosen the inner hub nut until it can be turned by hand, then again tighten the inner hub nut to 25 Nm. the lockwasher against the inner hub nut, it only goes in one way, it has a small inner tab that locates with the key way of the hub, this is between the threads. Once the lock washer is in the correct position, you can now install the outer hub nut, this outer nut must be torqued to 47 Nm, once you have tightened this outer nut, please once again check that the starting effort is correct.

Oct 18, 2013 | 2007 Toyota Hilux 2.5

1 Answer

Tire rod end left sidefrom gearbox is broken how do i dismantel


if its the outer tie rod than loosen the jam nut on the threaded part of the inner tie rod. You will then be able to unthread the outer tie rod from the inner. Count the number of turns and install the new one with the same number of turns.

If its the inner tie rod you will need an inner tie rode remover/installer tool and a torque wrench.

Feb 03, 2012 | 2001 Mercury Sable

1 Answer

Mechanic says inner tie rod needs to be replaced. How do I know?


Raise the vehicle and wiggle the wheels left and right. You would know which one has a play if its the inner or the outer. the inner tie rod connects close to the rack and pinion. The outer is close to the tire. Goodluck

May 28, 2011 | 2001 Ford Taurus

1 Answer

I want to know the distributor cap firing order along with the firing order on the engine


The ignition order for my 1988 Mitsubishi Mirage is Longest lead to left-hand outer piston, then left-hand inner piston followed by right-hand outer piston then right-hand inner piston., going in an anti-clockwise direction.

Oct 19, 2010 | 1988 Mitsubishi Mirage

1 Answer

I have a 1977 Dodge. Model # M500, removing inner dually tire


THE INNER STUDS FOR THE INNER WHEELS ARE NUTS AS WELL AND SECURE THE INNER WHEEL. USE A SQUARE DRIVE TO REMOVE THESE STUD/NUTS. DRIVER SIDE NUTS/STUD ARE LEFT HANDED(STAMPED WITH A BIG (L)). AND PASS SIDE RIGHT HANDED. THESE TORQUE SPEC OUT @ 400-450 LB FT. OF TORQUE, YOU WILL HAVE TO USE A CHEATER BAR OR HEAVY DUTY INPACT!

Apr 26, 2010 | 1983 Dodge Pickup

2 Answers

I need part number for the rear wheel bearings left and right , inner and outter for Daewoo lanos 2000 model


Daewoo rear wheel bearing parts numbers are
94535209 and 94535218....one each per side

Jan 06, 2010 | 2000 Daewoo Lanos

1 Answer

2003 pontiac grand prix inner tire rod , I need to change the tire rod


first take the outer tierod off of the spindle tthen take the boot loose from the rack and try to break the inner tie rod loose make sure when replacing the inner tierod that you count number of times you turn it wel unscrewing the outer tie rid you will need to get a alinment perform after you replace that tierod.

Nov 12, 2009 | 2003 Pontiac Grand Prix

1 Answer

How do you replace the outer tie rods on 2000 oldsmobile alero


Jack up vehicle; back off set nut that connects outer to inner tie rod; remove cotter pin and castle nut from outer ball socket of t/r end; take a 'pickle fork' and tap between joint and steering knuckle to separate; then unscrew the outer t/r from the inner t/r, "counting the number of turns until completely off. Run the new locking nut onto new tir rod end; turn t/r same number of turns, and lock set nut; runt the new post of t/r end back into steering knuckle, tap down with a hammer, and use new castle nut to tighten; insert new cotter pin and grease fitting; again tighted locking nut to inner t/r; grease new t/r end...good to go!

Jan 31, 2009 | 2000 Oldsmobile Alero

1 Answer

1995 toyota landcruiser diesil headlights


inner lights are highbeam outer lights low beam and side gaurd lights are your parkers, if you are 100% sure your globes are ok then your dimmer switch is stuffed this is the light switch in the cab that you use to opperate lights, sometimes the contacts get dirty inside the switch and create a short if you are mechanicaly minded then you could have a go at pulling it appart and cleaning it. if not you could get one from the wreckers in your area......

Aug 21, 2008 | 1995 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...